Building Automation Knowledge Base

Issue A Trend chart in TAC Vista Workstation is opened and set to show values for the last 4 months, but not all values are shown in the Trend chart. Product Line TAC Vista Environment TAC Workstation Cause The Trend chart can display maximum 50 000 values. So if you log often and want to display for example the last 4 months, only the latest 50 000 values will be displayed. Resolution There is no way around the 50 000 values limit for the Trend chart. To see all values for the last 4 months you need to create several Trend charts.

Warning Hazard of Electric Shock: Remove all power from all devices before removing any covers or doors of the system. Disconnect power at the device and at the power source. Electrostatic Discharge Required: Always discharge static electricity from your person by touching metal prior to handling any hardware. Failure to do so may result in damage to devices. Issue What are the steps for replacing a failed AC1 or AC1Plus IO module hosted under SP-AC1 controller with available module either brand new or previously used? Product Line EcoStruxure Security Expert Environment Security Expert Controller Continuum AC-1 IO Module Security Expert Server Cause Guidance needed on steps to replace a failed AC1/AC1Plus module hosted by SP-AC1 Security Expert controller Resolution While the recommended upgrade path is to replace any failed AC1 module with Security Expert IO module such as the SP-RDM2, it is possible to replace with same module type (AC1 or AC1Plus) using the steps below.   Take note of the failed module address, this can be done either in the "Module addressing" window or by looking at the "Physical address" field in the Reader Expander. Using Continuum Cyberstation (or CX9900 Net Controller 1 with terminal interface) set the ID of the replacement module to the same as the ID of the failed module. Remove the failed module and put the replacement module in its place, once power is applied, the COMM LED of the replacement module should blink normally. Re-start the SP-AC1 controller, this can be done either by cycling power to the controller or by performing a re-start in the controller's web interface from a web browser. Once the controller is back online, from the client go to Sites\Controllers, right-click the appropriate controller, and select "Module addressing", in the module addressing window you should see the failed module offline and registered, the replacement module should also be present using the same ID as the failed module but offline and NOT registered. Click on "Update modules" After the system displays "Update module command sent OK" wait a minute, then bring up the "Module addressing" window once again, the failed module should now be gone and the replacement module should now be online and registered. You should also see an entry in the "Status page view" for each module indicating the module has registered successfully.

Issue MP-V Air Flow is reading zero flow despite the Velocity Pressure having a positive value. Product Line EcoStruxure Building Operation Environment MP-V-7A, MP-V-9A, RP-V-4A, RP-V-5A Variable Air Volume Data Cause The Air Flow value is an internally calculated value based on the Velocity Pressure. There are a number of values involved in that calculation that could result in no flow. Resolution Validate Variable Air Volume Data > Flow Balance Data > Rated box flow. The rated box flow defaults to 0 ft³/min in a new controller and must be replaced with the rated flow at 1.0inH₂O (provided by the box manufacturer). Compare Variable Air Volume Data > Velocity Pressure > Value to the Zero flow threshold. Any Velocity Pressure below the threshold will result in no flow. This threshold defaults to 0.008inH₂O. Check Variable Air Volume Data > Properties > Balanced k-factor and Balanced flow correction factor. If either of these values are at 0, there will be no flow. These values cannot be directly written to and are only the result of a flow balance calculation. To get them to update: Go to Variable Air Volume Data > Flow Balance Data and record all balancing data (you will need to manually re-enter it later). Set all 7 balancing values to 0 - Rated box flow, Box/Hood measured maximum/intermediate/minimum Right-click on Variable Air Volume Data and Download Re-enter the valid balancing data. The balanced k-factor should now show a value close to the rated box flow and the balanced flow correction factor should show a multiplier ideally between 0.5 and 2. If the box has not been balanced and no valid balancing data is available, leave the minimum flow readings at 0 and enter the same value into both the hood and box maximums (for example, 1000 and 1000). This will result in a balanced k-factor equal to the rated box flow and a balanced flow correction factor of 1.

Issue After successfully logging in, the controllers' web page is only partially displayed, showing broken image links and incorrectly formatted text. Resetting the controller does not resolve the problem. SP-C Configuration Web Page Product Line EcoStruxure Security Expert Environment Security Expert SP-C SP-AC1 SP-ACX Cause Incorrect controller web page files have been cached in the browser. This may occur if different controller firmware versions are viewed/commissioned on the same PC.  Resolution Clear the web browser's cache and try again.  Connect directly to the controllers' configuration page. For a controller with default settings, browse to 192.168.1.2/config.asp.

Issue TGML graphic uses the NAM Standards component to display a SmartX Sensor Device with a dynamic cover model. The graphic always shows a blank faceplate instead of the correct face - 3 buttons, LCD, or Touchscreen. Product Line EcoStruxure Building Operation Environment SmartX Sensor Device (Living Space Sensor/Room Unit Device) NAM Standards Team Components TGML Library TGML Graphic Thermostat - SmartX Living Space Sensor - Dynamic AppRev1.02.05 Cause A script running inside the graphic component is expecting a well-formatted string representing the cover model on the cover model input binding. If that data is not delivered properly, the component defaults to a blank cover. Resolution Verify that the proper component is being used based on Sensor Firmware. Verify the proper IP controller firmware is installed to meet compatibility with the Host Server and also contain desired features. Once a controller is upgraded and the sensor has had time to upgrade, check the Sensor - Properties - Basic Tab - Application Software version. If greater than or equal to 1.02.05, then use Thermostat - SmartX Living Space Sensor - Dynamic AppRev1.02.05 Otherwise use Thermostat - SmartX Living Space Sensor - Dynamic   The TGML component should work as expected, but factors outside of the graphic can make it not work right. Click on the SmartX Sensor Device and look at Properties > Basic > Status Information > Cover model. Does that show a valid cover model (ex: SXWSCBXSELXX) or does it show ASCII gibberish? If showing nonsensical ASCII string, hotfix firmware is available to address this. Install firmware at or higher than 3.02.03.02109, which includes fix for Defect# 46054 and 47266 affecting the Cover Model SmartX IP Controller v3.02.03.02109 - Firmware Package File Release Date: 2021-Dec-19 https://ecoxpert.se.com/search?documentUUID=6b61d413-5cf8-47c0-ac4d-135391d375bf&title=SmartX%20IP%20Controller%20v3.02.03.02109%20-%20Firmware%20Package%20File Release Notes v3.02.03 - SmartX IP Controller Firmware Release Date: 2021-Dec-19 https://ecoxpert.se.com/search?documentUUID=1e29da8d-cf49-418d-92e5-e022bc4f33c7&title=Release%20Notes%20v3.02.03%20-%20SmartX%20IP%20Controller%20Firmware If the Cover Model is populated with a proper value, a previous firmware upgrade may have caused string values to stop writing properly through the TGML binding. There are two different resolutions to try in this order: Restart the AS-P Delete the SmartX Sensor Device (be sure to select "Keep references") and add it back as a new object with the same name and address.   The binding controlling the dynamic display of different cover models on the graphic can be overridden. Inside the TGML component are 3 groups named "3 Button," "LCD", and "Touchscreen." All are hidden. Find the proper face and change it to default to Visible. Find the Bind named "CoverModel" and delete the binding and script beneath it. This is what is responsible for auto-changing the cover and is no longer needed.

Warning Potential for Data Loss: The steps detailed in the resolution of this article may result in a loss of critical data if not performed properly. Before beginning these steps, make sure all important data is backed up in the event of data loss. If you are unsure or unfamiliar with any complex steps detailed in this article, please contact Product Support Services for assistance. Issue Orphan alarm exists in the Enterprise Server database and acknowledgment of the alarm does not remove the alarm. Product Line EcoStruxure Building Operation Environment Building Operation Enterprise Server v. 2.0.3 or lower,  Cause Backup of the Building Operation database that includes historical data will include the alarm that needs to be purged. IP changes or other reasons can contribute to alarms being orphaned. Resolution Note: Version 2.0.4 and from 3.0.2 and higher there is a built-in solution called Alarms Integrity Check which can be run to verify all alarms and purge any that are no longer in the system.     In order to completely purge an alarm database, it is necessary to delete the PersistedData.dat file that stores this information in the database. Perform an ES and AS full backups Using Building Operation Software Administrator click the "Stop Service" button for the Enterprise Server. Image from Windows XP Image from Windows 7 / 10 Browse to the database path listed in the Building Operation Software Administrator tool. Windows 7/10: C:\ProgramData\Schneider Electric StruxureWare\Building Operation 2.x\Enterprise Server\db Windows XP:  C:\Documents and Settings\All Users\Application Data\Schneider Electric StruxureWare\Building Operation 1.X\Enterprise Server\db Browse to the Persistent subdirectory Move/Delete the PersistedData.dat  file Click the "Start Service" button in the Building Operation Software Administrator tool. When the Enterprise Server restarts and you log in the orphaned events will be removed and any currently present alarms will return to the Alarm window with their proper status and assignment. This process causes a re-evaluation of alarms on the ES and fetches all the alarms from each AS. This can take a few minutes and may cause some slowness in the system. Note 1: Historical perspective of previous alarms, operator actions, or other data recorded in the Event Log will be lost in this process.  

Issue Information not available in product documentation. Product Line Satchwell Sigma Environment Windows versions Cause Documentation not updated to show additional operating systems now supported. Resolution Sigma 4.0.8.57, as a front-end user interface, is supported on the following operating systems: Windows XP Pro Service Pack 3 Windows 7 Professional Windows 7 Ultimate Windows Server 2003 Windows Server 2003 R2 Windows Server 2008 Windows Server 2008 R2 Sigma 4.0.8 (build 80 – 89), as an engineering tool for Sigma when transitioned into SBO/EBO Sigma is supported on: Windows XP Pro Service Pack 3 Windows 7 Professional Windows 7 Ultimate Windows Server 2003 Windows Server 2003 R2 Windows Server 2008 Windows Server 2008 R2 Sigma 4.0.8 (build 104 onwards), as an engineering tool for Sigma when transitioned into SBO/EBO system Sigma is supported on: Windows XP Pro Service Pack 3 Windows 7 Professional Windows 7 Ultimate Windows Server 2003 Windows Server 2003 R2 Windows Server 2008 Windows Server 2008 R2 **1 Windows 10 **1 Windows Server 2012 **1 The additional operating systems support is only applicable when Sigma is part of a SBO/EBO installation. (This confirmation was provided to PSS by R and D).  

Issue Valid reads for HID Corporate 1000 cards are showing up on two separate event lines when valid reads for 26 bit cards are showing on one event line. Card data on two event lines is not able to be added to a new or existing User through the right click menu in the status page. Corporate 1000 Cards As Two Events 26 Bit As Single Event Product Line EcoStruxure Security Expert Environment Security Expert Cause The card data is being split into two lines because of the length of the card data. The limit of facility code and card number for read raw events is 16 bits each, so the maximum value for a site code or a card number is 65535 before the data is split into two lines. Resolution A workaround for this is to streamline the process of adding cards to users. Use the New Window button on the Event Status Page, and then use the main window to navigate to Users. Position both windows so new events can be seen, and use the main window to add new cards in by typing the numbers manually. Side By Side User and Events Windows

Issue Method to show how to configure logging of reader tamper trouble inputs. Product Line EcoStruxure Security Expert Environment Security Expert Cause Reader tamper trouble inputs are not configured to log events by default. Resolution Reader tamper transitions can be logged as events by configuring the associated Reader Tamper Input. Browse to Trouble Inputs | Areas and Input Types. Assign an Area with an Input Type (suggest 24 HOUR Alarm or similar). When the reader is removed a Trouble Input <$$$$> Reader 1 Tamper / Missing (##) Opened event will occur two minutes later. When the reader is connected again the Trouble Input <$$$$> Reader 1 Tamper / Missing (##) Closed event will occur immediately.

Issue When configuring reports there is no option to select the report to be exported once a month. Product Line EcoStruxure Security Expert Environment Security Expert Cause There isn't an option to have a  report run only once a month. Resolution A workaround for this would be to select a single day of the week for it to run. This would reduce the frequency of the reports to once a week, then to have the operator check the export folder once a month for that months report.   Browse to the Event Report you want to export. Under File Export tab select the Enable File Export checkbox. Set the Time field to the time of day you want to run your report. Set the Export Directory to the folder you want to save your report export files to. Under Days to Export select one day of the week. Under Period select Last Month. Each time this report is run the same file will be overwritten, so when setting the report period to "Last Month" it will export the last months events from when it is run. Once a month the Operator would then select the file in the report folder which will have the last months events in it. The filename of the report is "EventReport" followed by that Event Reports Database ID number.

Issue A site is required to store Extended Trend Log historical data for an extended period of time, in order to make sure the system has enough capacity for all the data  it is necessary to calculate the storage needed ahead of time Product Line EcoStruxure Building Operation Environment Building Operation Enterprise Server Building Operation Workstation Cause Understanding the storage requirements for long term trend storage Resolution Formula to calculate the storage capacity needed for Extended Trend Log data. Storage in bytes (S)  = Number Of Records (N) x 70 bytes. EXAMPLE: Consider a trend log of 1000 records with a 10-minute interval, if the requirement is to keep 5 years of data, how much storage capacity will be required? The number of records would (N)  be... 6 records per hour times 24 hours per day times 365 days per year*** times 5 years (*** leap years must be taken into account) N =  6 X 24 X 365 X 5 = 262800 bytes This equates to: S = N X 70 S = 262800 X 70 S = 18396000 bytes or approximately 18 megabytes   Note - The calculations above are for the native SQLite database used by EBO. There are two alternatives to using the ES database for long-term trend storage. Report Server - See the WebReports Database Usage Calculator Knowledge base article for storage calculations External Log Storage is possible from EBO v3.0 using TimescaleDB database - The EBO External Log Storage Installer tool from the community provides a databases size estimator located under the Tools menu item

Issue Troubleshooting controllers can be aided by observing the CPU light Product Line Andover Continuum Environment Continuum controllers Cause A video created to show the differences between Normal, Error and Bootloader modes Resolution This will not show specifically what mode the controller is in, but it can offered to try to help to determine the mode. The speed of the CPU light on some of the controllers may vary, but this gives a general idea. Normal Mode is on the left, Error Mode is in the middle and Bootloader Mode is on the right. Note if the CPU LED is constant on or off see the KB article - Continuum controller CPU light solid or not illuminated

Issue Controller is unresponsive and does not respond to a hard reset or power cycle with the battery disconnected..  CPU light remains on constantly. Product Line Andover Continuum Environment InfinityController, b3 Controller NetController II, CX9680 ACX57 bCX Cause Controller stopped functioning after power cycled. Resolution Test controller with a known working PS power supply and/or test the supply voltage is correct If the controller still does not respond to a hard reset then return for repair. See the appropriate manual for reset instructions

Issue Connection issues come in a variety of flavors, narrowing them down is important to help resolve the issue. One of the causes of connection issues could be general network problems. Product Line EcoStruxure Building Advisor, EcoStruxure Building Operation Environment Building Operation Building Advisor EBO Health Module Building Operation Enterprise Server Building Operation Enterprise Central Building Operation Automation Server Premium Cause There are some steps that can be done to eliminate network issues as the cause of Building Advisor Cloud connectivity problems Resolution For the ES or EC: On the server running the ES/EC, start a WireShark capture then open up the command prompt running as admin and run the following commands. Make sure to note the responses received after each command: ping app.schneider-electric.com ping cnmiothubappstna.blob.core.windows.net ping cnm-ih-na.azure-devices.net curl -X POST https://app.schneider-electric.com/ecostruxure-building-advisor/diagnostics/Initialize -k -v --header "Content-Length: 0" Open the PuTTY application and telnet to the same 3 sites you pinged above over port 443. PuTTY is installed with Device Administrator and can be found in a folder similar to: C:\Program Files (x86)\Schneider Electric EcoStruxure\Building Operation 3.2\Device Administrator\bin If connection is successful, then you will only see PuTTY show blank black screen and it will remain without error pop-up for over 15 seconds. If unsuccessful, PuTTY will pop-up error for time out or network error, like:   PuTTY: Network Error For an AS-P/B: Connect to the server using Device Administrator and select the console option Run the following commands: ping app.schneider-electric.com ping cnmiothubappstna.blob.core.windows.net ping cnm-ih-na.azure-devices.net curl -X POST https://app.schneider-electric.com/ecostruxure-building-advisor/diagnostics/Initialize -k -v --header "Content-Length: 0" Curl response should look like the following (2 screenshots to show all): Command and Response Response (continued)

Issue Having trouble configurating EcoStruxure Building Operation to connect to the Building Advisor Portal. Product Line EcoStruxure Building Advisor Environment Building Operation Automation Server Premium Building Operation Enterprise Central Building Operation Enterprise Server Building Operation Building Advisor EBO Health Module Cause There are multiple server configurations that you can have to connect to the Building Advisor Portal Resolution The following are the most common configurations.   Stand-alone AS-P and AS-B SmartX servers  REQUIREMENTS: EBO version 3.0 or higher. Automation Servers with EBO 2.x do not support the Cloud Connectivity feature. Servers are connected directly to the EBO cloud provided these servers are running    ES/AS configuration REQUIREMENTS: EBO version 2.0 or higher. The ES is responsible for the communication and data transfer with the Building Advisor cloud on behalf of the downstream SmartX servers and requires    EC/ES/AS configuration,  REQUIREMENTS: Each server requires EBO version 2.0 or above. The EC is responsible for communication and data transfer with the Building Advisor cloud only for itself.  Cloud-connect settings only are needed on EC & get cloned to each ES.  Each ES is responsible for communication and data transfer with the Building Advisor cloud for itself and the downstream SmartX servers. 

Issue While using a demo license, the system is unable to connect to the Building Advisor Cloud Product Line EcoStruxure Building Advisor Environment Building Operation Enterprise Central 3.0 or later Building Operation Enterprise Server 3.0 or later Building Operation Automation Server Premium 3.0 or later Building Operation Building Advisor Portal Cause The Demo License of EBO does not contain the Cloud Connectivity feature. If the original system was registered in 2.0 and running on a demo license, once it is upgraded to 3.0 the Cloud connectivity will be lost. Resolution Enterprise Server and Enterprise Central Customers using an Enterprise Server or Enterprise Central must install a valid license to connect to the Building Adviser Cloud.   AS-P and AS-B Cloud Connectivity is only supported in versions 3.0.x or later. When running in a Stand-Alone configuration, the AS-P and AS-B do not require a separate license for Cloud Connectivity.

Issue How to calculate the required disk space that will be used by WebReports? How to know if SQL 2008 R2 Express (with Advanced Services) will have adequate storage space for the sites Reporting requirements? Product Line EcoStruxure Building Operation Environment WebReports 1.9 / 2.0 Cause Require the ability to forecast how much space will be required to store and retain data within the Building Operation WebReports database. Resolution The attached Excel Spreadsheets can be used to forecast how much space is needed to store and retain the Building Operation WebReports database. WebReports_DB Usage Calculator.zip WebReports_DB Growth Estimator 2.0.zip Note that SQL 2008 R2 Express only allows a database size of 10 GB, so if your configuration is more extensive than that you should probably consider using the full SQL Server 2008 R2 editions. As a quick indicator here are the record sizes for each object type stored in the report server database: Object Type Size per record (bytes)   WebReports versions <1.8 >1.9   Ext. Trend 140 165   Meter 170 140   Alarm 900 500   Event 400 520  

Issue At start up, anything requiring the SOAP Service to function will fail to work properly. Logging in to Web Client fails with a "No License found for SOAP Interface" message. The Data Sync Service will generate incorrect username or password error messages. Product Line EcoStruxure Security Expert Environment Security Expert SX-SOAP SX-DB-SYNC Cause The SOAP Service fails to start up properly after a Windows restart under certain conditions. Resolution 1. Set the Security Expert Data and (if installed) the Security Expert Data Sync Services to Automatic (Delayed Start). 2. Restart the PC.

Issue Cannot generate a report from Access Expert V2. Getting an error when attempting to generate the report "Could not load file or assembly Microsoft.ReportViewer.WebForms, Version=11.0.0.0"   Product Line EcoStrucure Access Expert Environment Version 2 Report Viewer Windows Cause The ReportViewer files that are from Feenics's website contain version 11. Microsoft does have older and newer versions of the file (i,e 10 and 12) so there is a potential that these files will not work. Resolution To resolve this issue 1. Download the Microsoft Report Viewer (Feenics Training> Web App V2> Miscellaneous Downloads) http://www.feenics.com/Downloads/ReportViewer.zip 2. On the Access Expert application PC (Not the SQL Server PC in a 2 PC system)     Uninstall all versions of Report Viewer and SQLClrTypes from Windows> Control Panel> Programs and Features 3. Stop the Feenics Keep Render Service 4. Unzip the Download files (Report Viewer.msi  and SQLClrTypes.msi) and install both of them 5. Restart the Feenics Keep Render Service Test Reports 6. If they are still not working, reboot the Access Expert PC and test again. If this is still not working, contact your local country support.

Issue Unable to add PIN to Users in a new v4.2.243 or v4.2.244 Database / Site. Errors similar to below are seen when attempting to add a new PIN.   Fig. 1 - PIN does not meet complexity requirements Fig. 2 - Could not generate a unique 4 digit PIN Product Line EcoStruxure Security Expert Environment Security Expert version 4.2.243 , 4.2.244 Cause The default PIN settings are not be set when the Site is first created during installation of a new Security Expert Database. Resolution Go to Global > Sites and click Save on the newly created Site object to set the default PIN settings.