Notifications

Ask Me About Webinar: Data Center Assets - Modeling, Cooling, and CFD Simulation
Join our 30-minute expert session on July 10, 2025 (9:00 AM & 5:00 PM CET), to explore Digital Twins, cooling simulations, and IT infrastructure modeling. Learn how to boost resiliency and plan power capacity effectively. Register now to secure your spot!

Building Automation Knowledge Base

Schneider Electric Building Automation Knowledge Base is a self-service resource to answer all your questions about EcoStruxure Building suite, Andover Continuum, Satchwell, TAC…

Invite a Co-worker

Send a co-worker an invite to the portal.Just enter their email address and we'll connect them to register. After joining, they will belong to the same company.

Send Invite Cancel

Related Forums

Intelligent Devices Forum

Previous Next

Invite a Colleague

Found this content useful? Share it with a Colleague!

Invite a Colleague

Label: "tac ia series"

View in: "Building Automation Knowledge Base" | Community

1826 Posts | First Used: 2018-09-06

Building Automation Knowledge Base

Issue When attempting a device browse in Workplace Tech 5.10.1, an error pop up, "CoCreateInstance(CLISD_RTApplication) failed" is invoked A critical error with Rtmonitor.exe when running Workplace Commissioning Tool Product Line TAC IA Series Environment Workplace Tech => 5.10.1 Workplace Commissioning Tool => 5.10.1 Windows OS 32 bit Cause Environment Variables /variable/path includes the incorrect path to the LonWorks\bin. This doesn't allow the rtmonitor.exe to be executed. Resolution When the Workplace Tech 5.10.1 bundle of applications are installed, the Environment Variables is modified to include, %ProgramFiles(x86)%\LonWorks\bin In a 32 bit OS, this ProgramFiles(x86) folder does not exist. This path has to be modified so the assets can be found. Remove the "(x86)" so the path appears as below. Note: This is only applicable for 32 bit operating systems.

Issue The following error occurs on startup following upgrading of Niagara Station to 4.10. SEVERE [20:42:01 23-Oct-20 UTC][nreconfig] invalid nre memory configuration values, 832 > 816 Product Line TAC IA Series Environment I/A Jace 8000 N4.10 Cause The default NRE memory pool settings are incorrect after an N4.10 upgrade and need configuration to function correctly. Resolution Niagara 4.10 and Default NRE Memory Pool Changes The increased size of some core libraries in Niagara 4.10 required changes to the default NRE Memory Pool settings for use on a JACE-8000. MetaSpace memory needed to be increased to allow applications to run without issue. Note: Any previous custom memory configuration applied to the JACE-8000 will be reset upon upgrade to 4.10. The overall size of the pool of memory available to the NRE installation has decreased. T As the overall size of the pool has decreased, customizations based on the old total pool size are invalid and cannot be maintained. If a custom memory configuration is required, the user will need to manually adjust the platform administration menu after a device is upgraded. A longer-term approach to address this issue is in development and should be available with the Niagara 4.11 release. NRE Memory pool default settings for Niagara 4.9: Changes to the default configuration: Heap Space size 4.9 value: 384 MB 4.10 value: 360 MB Meta Space size 4.9 value: 48 MB 4.10 value: 56 MB System reserve 4.10: allocated additional 16MB NRE Memory pool default settings for Niagara 4.10:

Issue Where are the DUI expander objects for the MNB-300 and MNB-1000 controllers in Workplace Tech? Product Line TAC IA Series Environment I/A Series WorkPlace Tech version 5.1 through 5.9.4 I/A Series WorkPlace Tech version 5.10.0 till current Cause The standard stencils do not include an object for Momentary SS or a DUI multiplexer. Resolution The I/A Series BACnet controllers do not currently support the DUI object directly within the MNB-300 or MNB-1000. An application performing the same basic function was created and factory tested. This application was created as a custom object named "DUI_App". For support of these objects in Workplace Tech 5.1 until 5.9.4, log into The Exchange Download Center and download the file Application Objects_rev1.zip. There is also a detailed DUI_Application_Documentation_rev1.pdf that describes the operation of the "DUI_App". For support of these objects in Workplace Tech 5.10.0 until further notice, log into The Exchange Download Center and download the file Application Objects_rev2.zip. There is also a detailed DUI_Application_Documentation_rev2.pdf that describes the operation of the "DUI_App". Note: VAV box controllers do not have DUI expander objects available. See TB06-02 for additional details.

Issue What utility in Windows XP can disable items in Startup? Environment Windows XP Cause Items that run on startup can sometimes make the boot up process for a PC very slow. Depending on which applications have been added to start automatically on startup, it can also cause problems if things load in the incorrect order. Resolution Click the Start button in Windows XP Select Run Type msconfig and click OK.

Issue When opening (pull up) sunblind, it stops at the end of runtime and then rolls back down. When closing (pull down) sunblind, it stops at the end of runtime and then rolls back up. Environment Lonworks devices including REG-N MSE4 (SVEA 32237-346) Sunblind actuators Cause The sunblinds only have UP/DOWN functions, and there is no panel angle setting. The sunblinds are not venetian, just simple sunblinds. The sunblind actuator is preconfigured for use with venetian blinds. For example when driving down completely first the motor is energised for the time configured in UCPTdownDriveTime, then stops a short moment and then turns the angle of the lamella by energising the motor for the time configured in UCPTpanelTurnTime (dependent on the value of parameter UCPTdownPanelAngle). Resolution When not using venetian blinds the parameters UCPTdownPanelAngle, UCPTupPanelAngle, UCPTpanelTurnTime and UCPTpanelTurnTimeBottom should be set to zero. Commands to the sunblind actuator then should as well have the value of zero in the rotation part of the SNVTsetting command.

Issue Change an IP address on Windows 8 to a static address. Product Line Other Environment Windows 8 Cause Changing the IP address of a PC is often done to ensure it resides on the same subnet and network as the system or devices it is trying to communicate with. Resolution From the Start Menu (Tiles), open the Charms bar by moving the mouse to the right bottom corner of the screen or press the Windows Key + C and click on Search. Highlight Settings. In the Search box type Network to search for any network related options From the list options choose Network and Sharing Center. From the View Your Active Networks section, select Local Area Connection. Go to Properties. Result: The Local Area Connection Properties screen appears. Highlight Internet Protocol Version 4 (TCP/IPv4) and click on Properties. Result: The Internet Protocol Version 4 (TCP/IPv4) Properties screen appears. Click Use the following IP address. Complete the configuration fields as shown below. This part of the configuration requires attention to detail, because one error will prevent you from getting on the network. Be sure you have this information at hand when you start to configure the TCP/IP protocol: IP Address: x.x.x.x Subnet mask: 255.255.255.0 Default gateway: x.x.x.x Enter these numbers in the appropriate fields and click OK. Continue to click OK or Close as appropriate until you return to the Network Connections screen. The Local Area Connection icon text should now say "Enabled". To test the new IP address: Open a command prompt in Windows 8 Swipe to show apps screen Scroll down and locate Windows system section heading Under Windows system, press or click on Command Prompt (a new Command Prompt window will open up on the Desktop.) You then can type in IPCONFIG then hit Enter and look for the new IPV4 address. You can also try to type in PING (IP ADDRESS) that should reply with the new IPV4 address if set correctly.

Issue Some helpful basic IP commands. Product Line Other Environment Computer with IP NIC or Network Cause Need for basic IP configuration or IP address Resolution Go to start, click run and type in "cmd". This takes you to the command prompt. Type in: "ping xxx.xxx.xxx.xxx" to see if your device is online and its response time. Make sure you put the space between "ping" and "xxx". "ipconfig" and hit enter to get the info of the computer you are currently using. You'll get the IP address, subnet mask and the gateway. "ipconfig/all" and hit enter to get more info on the machine your using. It will give you all the above and then some including the DNS server addresses. "tracert xxx.xxx.xxx.xxx" and hit enter and you can see the servers that you are going through to get to your destination. This can be used when connecting to a Loytec or a iLon and the IP address is being presented to the L-IP or iLon is unknown. Connecting through a firewall/gateway/NAT server, you are not presenting the PC's address - when you do the tracert you will go through your gateway and the next address will be the IP you are presenting- Use this in the iLon as the LNS server address.

Issue What is the contact information for Barber Colman Dyna group? What is the contact information for Barber Colman Aerospace division? What is the contact information for Barber Colman Industrial Instruments division? Environment Barber Colman Cause The old Barber Colman Dyna group is now a part of Woodward Governor. The old Barber Colman Aerospace division is now a part of the GE Aerospace. The old Barber Colman Industrial Instruments is now part of Eurotherm, an Invensys company. Resolution Barber Colman Dyna group is now Woodward Governor. They can be reached at 800-543-5811 Barber Colman Aerospace division is now GE Aerospace. They can be reached at 815-637-3500 Barber Colman Industrial Instruments is Eurotherm, an Invensys company. They can be reached at 815-637-3222 or 815-637-3404 for tech support.

Issue The Echelon LonTalk PCC-10 PCMCIA Network Adapter will not work with a Dell E6410 laptop. Product Line Satchwell MicroNet, Satchwell Sigma, TAC IA Series, TAC Vista Environment Echelon LonTalk PCC-10 PCMCIA Network Adapter Dell E6410 laptop Cause Dell E6400 Chipset Resolution To correct this, an entry needs to be added into the Windows registry. Option 1 Download a Windows registry import file from The Exchange. Navigate through Products > Satchwell > Sigma or MicroNet > Downloads > Hot Fix (Or you can download the file here RegedittoaddPCMCIACard.zip). Once downloaded, double click the file and the entry will automatically be added. Reboot the computer before the entry is read. Option 2 Manually add the entry into your registry. Use caution when making changes to the Windows registry. Mistakes can be fatal to the operating system. To manually add the entry, carry out the following: Go to Start > Run and use “regedit” to open the Windows registry. Navigate through to HKEY_LOCAL_MACHINE\SYSTEM\ CurrentControlSet Services Pcmcia Parameters Add a new DWORD entry called “IrqRouteToPciController” Modify the new entry and give it a hexadecimal value of 8 Reboot the computer before the entry is read. If option 1 or 2 do not resolve the issue, it may be necessary to perform the following: Option 3 Open the registry editor. Go to the registry entry HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{68EE3401-D4CA-11D3-8DBB-0060082936F2} or HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{68EE3401-D4CA-11D3-8DBB-0060082936F2}\0000 and look for the key name "PcmciaExclusiveIrq". Delete the key name "PcmciaExclusiveIrq" (If it exists). You may need to reboot the PC. Further information may be available in the Echelon Knowledge Base on the Echelon website. This information can be found in Solution: KB763. For more information, please refer to TPA-SACH-10-0009.00 - LON PCC-10 PCMCIA Card with Dell E6410 Laptop

Issue The xif file needs to be uploaded without LNS Management Tool All the devices on the LonWorks network needs to be searched The device mode or state needs to be changed Product Line TAC Vista Environment LonWorks Network Cause A LonWorks network test and diagnostic tool are needed. Resolution NodeUtil is a Windows console application that can be used with Echelon’s family of network interfaces (including the PCLTA-20, PCLTA-21, PCC-10, i.LON® 10, i.LON 100, i.LON 600, Loytec Devices, SmartServer, SLTA-10, U10, and U20 network interfaces) to diagnose and configure LonWorks® network interfaces, routers, and devices. NodeUtil is a test and diagnostic tool - it is not a network management tool. It will not assign destination addresses or bind network variables. Nor will it format LonMark® interoperable device information. This tool can be used in the following conditions: The xif file needs to be uploaded without LNS Management Tool All the devices on the LonWorks network needs to be searched The device mode or state needs to be changed Other network test and diagnostic need This software can be downloaded at http://www.echelon.com/support/downloads/detail.aspx?partNum=153-0373-01A The username and password are needed. This site is opened to the public for registration, so everyone can obtain it. Once you are logged in by default "Recommended Downloads" will be selected. Select "Development Tools" instead to locate the NodeUtil software.

Issue After installation of G3 Workbench version 3.4.57 or 3.5.25, the Software Manager on the Localhost may display that the sun-jre-win-x86 VM module is out of date: Environment Niagara G3 version 3.4.57 or 3.5.25 Sun JRE VM Module Cause While this is not a fatal error condition, the module can be updated. NOTE: if the installed version is 3.5.25, replace path references to "3.4.57" in the paths with "3.5.25" Resolution Shut down Workbench Open Windows Explorer, and navigate to the C:\niagara\niagara-3.4.57 directory Rename the jre folder to jre.old Now, navigate to the C:\niagara\niagara-3.4.57\sw\1.6.0.20 directory. Using WinZip, open the sun-jre-win-x86.dist file (or the sun-jre-win-x64.dist file if using the 64-bit version of Workbench). Select all of the folders in the archive, and extract them to the C:\niagara\niagara-3.4.57 directory (see below). Make sure that the “Use folder names” (or equivalent) box is checked. After the extraction, a new jre folder is created. Run the Platform Daemon (Start > Programs > Enterprise Network Server 3.4.57 > Install Platform Daemon) Open Workbench, and then open the Software Manager in the Platform. The Sun VM will now show "Up to Date"

Issue Are the Network 8000, DMS, and Signal manuals available in an electronic format? Environment Network 8000 DMS Signal Cause Option to view Network 8000, DMS, and Signal manuals in electronic format. Resolution The Network 8000, DMS, and Signal manuals are available from the Publication Zone via iPortal. They are, also, available on a CD. The "Legacy zip" link downloads and extract the files, if running the program from a computer or creating the CD. When running the program from a computer, launch "index.html" located in the extracted bin folder. Email legacy product documentation requests to be added to the Legacy CD, to Product Support.

Issue What is the recommended method to upgrade a Niagara R2 station to a newer version? Product Line TAC IA Series Environment I/A Series Niagara R2 Cause Unsure how to upgrade station databases. Resolution The published upgrade procedure is provided in F-27334. Below is a modified method that also works. Doing station upgrades on the server first is preferred. If there are any errors, they can be addressed without operational interruptions. Using the existing version of WorkPlace Pro (WPP), backup ALL of the UNC and Server databases into XML format. Methods of backing up and converting databases. Open the Enterprise server in WorkPlace Pro. Double click the station name. Select "Commands" and "Backup XML to save the server in XML. Then select "Backup Subordinate XML" to pull all of the UNC databases as XML into the server stations folder. If not on site but the UNC and Server databases are available, use the DB Admin tab of the Admin tool to convert the databases locally to XML. Now install the newer Niagara revision onto the Server. Copy the stations containing the XML files to the desired WPP revision station folder. Enable and open the new revision of WPP. Use the Admin Tool to convert locally all of the stations from XML to DB. (If there are any errors, they can be addressed without affecting the running installation.) After all the databases have successfully converted to DB, convert them to SNS. (This saves time later if the UNCs need reloading) Use the Enterprise Server to upgrade the UNC. During the upgrade process of the UNC it will ask to backup the database. If the database had upgraded with no issue in the previous step, enter the username and password to proceed with this backup. This will backup the station, upgrade the UNC, and then upgrade and reinstall the station. The previous station upgrade will be needed only if there is an issue. If after following this procedure the station still fails to start, contact Product Support Services.

Issue The Momentary Start / Stop (SS) object in a MNB controller is not working. The OutStrt output property remains ON and does not pulse off. Product Line TAC IA Series Environment MNB controllers Cause Application programming Resolution The OnPulse input property is set higher than the required minimum of 2 seconds. In order for the logical outputs to work (OutStrt & OutStp), physical hardware tags must be assigned to the physical outputs (AddrStrt & AddrStp). This is required when using the Momentary SS object in any MNB controller. The following logic can be used in place of the Momentary SS object to generate an equivalent OnPulse.

Issue The MNB-Vx appears in the Workplace Commissioning Tool in a read-only mode. After downloading a MNB-Vx controller, an error window appears stating "The download was completed but the application was invalid. The device is now running the factory default application". Product Line TAC IA Series Environment MNB-Vx Workplace Commissioning Tool Cause This condition is related to improper AC power provided to the MNB controller. Typically, when AC power drops below 20 Vac, the controller will fall back to a factory-installed application and switch to read-only mode in the Workplace Commissioning Tool. Resolution Fix the AC power supply so that it is within specifications for the MNB controller. Do a hardware reset using the dip switches to get it out of read only mode. Try the download again.

Issue How to display the degrees symbol (°) in WorkPlace Tech. Product Line TAC IA Series Environment WorkPlace Tech Cause Helpful to add a suffix for temperature engineering units. Instead of typing "degrees" or "deg". Resolution In the Constant Object properties (double click or right click - Set Value), click in the Suffix Text field. Desktop PC: If you have a desktop PC with a full keyboard, press and hold the Alt key and type the number 248 on the numeric keypad. Note: The number keys above the keyboard will not work. Notebook PC: The numeric keypad on a notebook PC is overlaid on the letter keys (M, J, K, L, U, I, O, 7, 8, 9), and requires that the Fn key is held down while using this secondary purpose. The Fn key may be colored blue to match the number keypad keys. Press and hold both the Alt and Fn keys and type the number 248 (KU8). Release the Alt key (and Fn key on the laptop). A small circle ° (the symbol for degrees) should appear. Type an upper case F for Fahrenheit or C for Celsius. Click OK. Other ASCII symbols are defined at asciitable.com or lookuptables.com.

Issue How can two Niagara G3 stations run simultaneously on a computer? Product Line TAC IA Series Environment Niagara G3 PC Cause To run two stations simultaneously on a PC, you must set up two ports to be different: The http port and the Fox port. Resolution Open the second station offline via My File System – Sys Home - Stations. Go to Services – Web Services – Properties – Http Port. Change it from 80 to 8080. In the offline station, go to Drivers – Niagara Network – Properties. Expand the Fox Service and change the Port to 1912. Be sure to save the changes and the bog file. Go to Platform – Application Director. Start the second station that you just edited offline. You should see the new ports under "Details." Go to File - Open Station. Enter the IP address, but change the port to 1912. You should now be able to go to the Niagara Network and discover one station from the other on the same IP.

Issue How can a connection be traced in a WorkPlace Tech drawing when it is difficult to see the wire path? Product Line TAC IA Series Environment WorkPlace Tech Cause When working with objects that have numerous connection wires (perhaps an uploaded drawing), it may be difficult to see the wire routing path. The link style is too small, which may be difficult to see the wire routing path. Resolution Click on a wire to select it (green handles appear). Two clicks may be required, since the first click selects the object that the wire is from. Right click on the wire and select Format/Style. In the Line Style pull-down menu, select "Error Box" (a heavy red wire). Click OK Trace and edit the connections as needed.

Issue In Niagara G3 Workbench, how can the size of the wire sheet be adjusted? Product Line TAC IA Series Environment Niagara G3 Workbench Cause Locating the settings to configure the Wire Sheet width and height to increase or decrease the view. Resolution Wire Sheet maximum size limits Starting in NiagaraAX-3.6, you can limit the size of the wire sheet by setting size of the wire sheet in the Options dialog box. From the workbench main menu, select Tools > Options to open the dialog box. Then select the Wire Sheet option and enter a desired maximum value in the Max Width and Max Height fields, as shown, below. Click the OK button to complete the setting change. If you decrease the maximum wire sheet size, objects are repositioned to stay within the view, after the size change. Note: You may need to refresh the wire sheet view to see the changes in wire sheet size and object repositioning. Also, the wire sheet borders may not be visible until you zoom out in the wire sheet view.

To The Top!

Building Automation Knowledge Base

Related Forums

Intelligent Devices Forum

Workplace Tech 5.10.1 Rtmonitor.exe Error

Default NRE Memory Pool Configuration Changes In N4.10

DUI Expander Objects for BACnet Devices in WorkPlace Tech

Disable items in Startup in Windows XP

How to find the IP address information on a PC?

Controlling LonWorks sunblind actuator results in incorrect end position

Assign a static IP address on Windows 8

Some helpful basic IP commands.

Contact Barber Colman

The Echelon LonTalk PCC-10 PCMCIA Network Adapter will not work with a Dell E6410 laptop

Tool for LonWorks Network Test and Diagnostic - NodeUtil Node Utility

The Sun JRE VM Module shows "Out of Date" after Installation of Niagara G3 version 3.4.57 or 3.5.25.

Are the Network 8000, DMS, and Signal manuals available in an electronic format?

What is the recommended method to upgrade a Niagara R2 station to a newer version?

Momentary Start/Stop object OutStrt output property remains ON without pulsing off in MNB controller

MNB-Vx download error "The download was completed but the application was invalid"

Display the degrees symbol in WorkPlace Tech

Run two Niagara G3 stations simultaneously on a computer

Trace a connection in a WorkPlace Tech drawing when it is difficult to see the wire path

Adjust the size of the wire sheet in Niagara G3 Workbench

Building Automation Knowledge Base

Related Forums

Welcome!