Issue A jobsite of MNL controllers was done with WorkPlace Tech 4.x.  The original databases are no longer available.  Can they be uploaded with WorkPlace Tech 5.x and will the upload convert them from 4.x to 5.x? Environment WorkPlace Tech versions 4.x and 5.x MNL controllers Cause Loss of original controller databases Resolution Uploading a MNL controller's program does not change anything within the controller.  Only downloads do. If a MNL controller was programmed with WorkPlace Tech 4.x and is uploaded with WorkPlace Tech 5.x, the uploaded file can only work with version 5.x.  If the resulting file is then downloaded to the same controller, the program version in the controller will then be at 5.x.  It will no longer work with 4.x.

Issue Upgrading an AS results in an empty database. Product Line EcoStruxure Building Operation Environment StruxureWare Building Operation 1.0.0.173 to 1.1.0.264 StruxureWare Building Operation 1.1.0.362 to 1.2.0.767  Cause When upgrading the database, the Enterprise Server (ES) upgrades without error, but when upgrading the AS, the result is an empty database. Resolution StruxureWare Building Operation 1.0.0.173 to 1.1.0.264 The problem is caused by the initial engineering of the system being carried out on an old AS that was not LON or BACnet specific, copying into new hardware at R1.0 then when upgraded to R1.1 the upgrade fails due to the wrong type of AS being used (LON or BACnet). This practice is not common place and rather rare. When the trace log is examined, they find that the upgrade fails due to the fact that an illegal object type is attempted to be created – a BACnet interface. This is not legal in an AS-L. The reason that this occurs is that the backup file is from an AS-L that had been restored from a 1.0 AS-B backup file. Check New Release or Upgrade StruxureWare Building Operation Site Software. The issue you face could possibly be a procedural one and this article clearly defines the steps. StruxureWare Building Operation 1.1.0.362 to 1.2.0.767 The solution is identifying problems with a period, space, or other character in names. Placing a period at the end of a name or accidentally having a space at the end is suggesting something is following or further action. If using BACnet, please see the note below. Problems with bindings which were still in tact when values were removed also are a potential issue and not properly removed.    Work Around: Backup AS Upgrade PC to 1.2 Open Device Administrator Upgrade AS to 1.2 DO NOT close Device Administrator Open StruxureWare Workstation Log into AS If Database is Blank go back to Web Browser Connect to AS Log in In the top right hand corner of the screen select Setting>Device Configuration Select the Server Log tab Click “Get all log files” Once downloaded, open “trace” using Notepad Click Edit>Find Type the word “nsp.csc.UpgradeManager ERROR:” The error lines run from date stamp to date stamp so isolate the line beginning with the year and ending with the next instance of the year. Here is an example: 2012-08-29 16:39:32.990 [32] nsp.csc.UpgradeManager ERROR:    Error Parsing Dump Objects:  RecoverableException: source/Path.cppy) ) Error: Invalid_Path (0x10001), module Coml(11), moduleCode 0, dispString "Heatsink Temp.", techString "Path& Path::Append(const UTF8String& name)"  The “dispString “_______”” section of this line will give you the object name that contains an illegal character. Downgrade the AS back to 1.1 Locate the dispString object and change the name so that it does not contain any illegal characters. This is typically a name ending in a period. NOTE: when the rename dialogue pops up, it will indicate that an illegal character is present to confirm you are modifying the right object. Backup the AS Re-Upgrade the AS to 1.2 If the upgrade fails, repeat steps 9-20 or call product support. Be prepared to provide a Db backup at 1.1 as well as the trace file from the 1.2 failed upgrade. BACnet Note: A BACnet device including an object name "East Duct Max." is no longer valid because of the illegal character at the end of the name. Before upgrading the ES from 1.1 to 1.2, remove any full stops/periods from any object names. "East Duct Max." is changed to "East Duct Max"  Other illegal characters include *°?|/"<> or ~ and an object cannot begin or end with a white space or period. Select TPA-SBO-12-0008.00 - ES upgraded from 1.1 to 1.2 loses database to review this TPA.

Issue Receive “Timeout while waiting for server to get ready” error when starting PCT Product Line EcoStruxure Building Operation, Project Configuration Tool Environment Project Configuration Tool, PCT Cause PCT can't reach DHCP-server from the virtual machine. Resolution To configure a port group or virtual switch to allow promiscuous mode: 1.Log into the ESXi/ESX host or vCenter Server using the vSphere Client. 2.Select the ESXi/ESX host in the inventory. 3.Click the Configuration tab. 4.In the Hardware section, click Networking. 5.Click Properties of the virtual switch for which you want to enable promiscuous mode. 6.Select the virtual switch or port group you wish to modify and click Edit. 7.Click the Security tab. 8.From the Promiscuous Mode drop  down menu, click Accept. Note: The setting on the port group overrides the virtual switch setting. For more information, see How promiscuous mode works at the virtual switch and portgroup levels (1002934).  

Issue CSMC 3805 Codes, CSMC User Guide. Environment CSMC3805 CSMC CSMC 3805 Cause There is a code displayed on the controller screen. What does this mean? Resolution The codes display the plant status under certain conditions. They are as follows: L05 = Return Water Temperature Low Limit. F = Water Frost Limit (Flow or Return). L01 = Inside Low Limit (Frost). H4 = Flow Water High Limit. A = Alarm (If alarm display is not required set code B61 to 1). 0 to 9 = Optimiser Status (only displayed if code B49 is set to 1). The User Guide can be downloaded from here.    

Issue When using the Modbus RTU X Driver to communicate to multiple Socomec Diris A20 electric meters it has been found only 2 or 3 devices can be networked together, even using a b-Link to boost the signal does not resolve the issue. Product Line Andover Continuum Environment Modbus RTU X Driver on bCX1 or Netcontroller II B-Link repeaters Cause The Socomec Diris A20 meters require a minimum of 4V RS-485 signal to communicate reliably, but the EIA RS-485 standard only calls for a +/- 1.5 volts signal and the Receiver Input sensitivity should be +/- 200mV. When using a bCX1 with the X Driver on Comm1 you will require a b-Link to provide the RS-232 to RS-485 conversion, although the B-Link fully conforms to the EIA RS-485 standard it does not have the drive levels required by the Socomec products. Resolution To resolve the non standard electrical requirement of the Socomec Diris meters use a Socomec RS-422/ RS-485 Repeater this will output the required electrical levels required by the Diris meters, the Socomec  part reference is 48990120.  Please refer to SOCOMEC Communication accessories or RS-422/485 Repeater Operating Instructions   If a B-Link is to be used each RS-485 output that is used will require a separate Socomec repeater.  

Issue How to set the Network 8000 MicroZone II (MZ2) back to its factory-default settings? Environment Network 8000 MicroZone II (MZ2) Cause Need to set the Network 8000 MicroZone II (MZ2) back to its factory-default settings Resolution See Technical Bulletin 95-08 for a detailed procedure. Revised 12/22/2011

Issue How are two 4-20 mA loop-powered sensors wired into a MNL-200? Environment MNL controllers with at least two UI inputs (MNL-100, MNL-150, MNL-200, MNL-800) Cause n/a Resolution The image below provides a basic (but accurate) diagram of two loop-powered sensors and how they are wired with a power supply and a MNL controller.

Issue Unknown meaning of object status numbers and descriptions Product Line Andover Continuum Environment Continuum Cyberstation Cause Continuum uses object status numbers and descriptions for diagnostics.  A list of these enumerations is required. Resolution See file Stsvc.txt in the Continuum directory In Continuum Versions 1.5 and higher, a new database attribute exists. This new attribute is "ObjectStatus". When the value of an object in the Continuum system is greater than zero, then an indicator icon is placed on that object in the explorer view. This indicator icon is also placed on the parent object and subsequent parent objects as applicable. This indicator icon will reveal the reason it has been placed on the object when you place your mouse over the indicator icon. This ObjectStatus attribute value is a bitwise type of attribute. ObjectStatus values and their descriptions: 0   - No mouseover, display normal 1   - Requires a Save from Controller (Parent) 2   - Requires a Save from Controller (Child) 4   - Requires a Flash Backup 8   - Object must be reloaded 16  - Object has been offline edited 32  - Object has been offline created 64  - Flash backup disabled 128 - OS update fail Combination values will display more than one description.  For example, 144 would display OS Update Fail and Object Has Been Offline Edited

Issue Need to be able to read and write to a point. Environment StruxureWare Building Operation Workstation ES AS Cause Need to be able to read and write to a point. Resolution Declare the point as Output and bind it. Outputs can be read and written.

Issue Netcontroller is running slowly or occasionally goes offline (bCX NC2 ACX CX) Product Line Andover Continuum Environment Continuum Netcontroller, Net Controller, Infinet, MSTP, Bacnet, Xdriver, x-driver Cause There are various reasons why the operation of one or more Netcontrollers and or attached controllers is slow and/or goes offline occasionally.  This guide is primarily to help collate the right information which may identify the issues.  If the reason cannot be identify then this information can be provided to support for further analysis. Resolution General troubleshooting techniques should be used. Define the exact problem. What exactly is slow? eg. Sending to the controller or its connected devices, opening or refreshing graphics, opening or refreshing points, updating Xdriver points, saving programs, creating new points. Is the controller slow from all cyberstations? Is the controller always slow? If not then try to find what makes it go slow, it is time related? Can certain steps be taken to cause the slowness or offline to happen? Get a screen capture of any errors. Gather site information. Continuum version, Continuum hotfixes and service packs applied, number of Cyberstation. Cyberstation operating system, details of Ethernet network and subnets used, with BBMD information of Bacnet sites (Asbuilt or a spreadsheet with IPs, etc.) Continuum Analyzer report, site controller map or spreadsheet or text dump Check the PCs running Cyberstation, do they meet the system specifications? Gather controller information What is the Scan rate? Is the controller time sync. correct? How many objects are on the controller, how many programs are running? What is the firmware version of the netcontroller and b3 or i2 controllers? Ethernet connection - Is the controller on the same subnet as the Cyberstations? A wireshark trace may help to establish the quantity of traffic on the Ethernet (See Using WireShark to analyze communications on an Ethernet network) Comms Ports - XDriver being used? What is on the comms ports? Xdriver (how much communications, points etc) Comms Ports - Bacnet MSTP - How many b3 controllers? How much extended logging? How many alarms being sent? How many 3rd party devices? Look at bacnet settings, how many values are being sent across the network? Check COV settings. Try removing the MSTP cable from the bCX (there could be an issue with an MSTP device causing the bCX to go offline/go slow) Comms Port - Infinet - How many infinet controllers? How much extended logging? How many alarms being sent? Look at infinet settings, how many values are being sent across the network? Check port reconfigs and errors. Try removing the infinet cable from the NetController (there could be an issue with an infinet device causing the NetController to go offline/go slow) Comms Port - other. Again try removing the comms cable from the NetController (there could be an issue with a device on this network causing the NetController to go offline/go slow) Run the Controller error log tool to gather the controller errors See Gather Continuum Controller error logs if requested by Product Support for troubleshooting If the controller goes offline, run the alarm listview.  Does it line up with the Controller error log? Check the CPU LED flash rate on all connected devices (i1, i2, b3 etc) as Can't bring bCX online in Continuum but do get a response to pinging its IP address, also the RD and TD LEDs should be checked for anything unusual This guide is primarily to help the on site engineer by helping them to assess the site. If there is still a need to contact support, please review and record as many items above as possible and send them to the case owner.  Further tests can be carried out including an ACCtrace to determine if the restriction could be at the Cyberstation, See How to capture Continuum Cyberstation activity using ACCTrace NOTE: Ensure all Cyberstations, Controllers and other laptops used for logging are in time synchronization before recording any logs. If it is believed there is an issue with the Infinet or MSTP network see Infinet and mstp bus troubleshooting If it is believed the problem is with extended logging see Extended Logging gaps, performance and load balancing It is possible that something connected to the controller causes the controller to go offline, try disconnecting all other cables and connections to the controller and then re-testing Where a controller is offline when connected directly to a PC/Laptop, try resetting the IP address, otherwise the controller will probably need replacing. NOTE Disconnecting all networks from the NetController is often a good starting point (reconnected IP/Ethernet cable)  

Issue Enterprise Server does not start when computer is started/rebooted or shuts down right after starting it StruxureWare Building Operation Software Administrator log shows the following error: nsp.NspServer The server has made too many unsuccessful attempts to start... Product Line EcoStruxure Building Operation Environment Software Administrator Enterprise Server Cause StruxureWare Building Operation is prohibiting the Enterprise Server from starting up because the ES has exceeded the number of startup retries defined in server_startup.properties. When the server_startup.properties file is opened in a text editor, the first line indicates a startup failure. NspServer.Startup.Service.Status: fail Resolution Windows XP: This is caused by a dependency, set in the registry, on the service netprofm (Network List Service), which exists on Windows Vista and later, but not on Windows XP. The error has been verified on a new installation of Windows XP. Steps 1 and 2 below help to resolve this on the XP operating system. Windows 7 and Windows Server 2008 R2 including Virtual: Start ES manually from the Software Administrator. If this fails, the log in the Software Administrator explains why. Start the ES manually from the Services listed in Services (Start, My Computer, right-click, Manage, Services click the + to find Services) find StruxureWare Enterprise Server Go to the Software Administrator and modify the HTTP, HTTPS, and TCP ports to available ports. (suggested: 81, 444, & 4444). The number of startup retries is defined in the following file: 1.2.0 and below : C:\Program Files\Schneider Electric\StruxureWare X.X\Enterprise Server\etc\server_startup.properties 1.3.0                  : C:\Program Files\Schneider Electric StruxureWare\Building Operation X.X\Enterprise Server\etc\server_startup.properties 1.4.1 and above : C:\ProgramData\Schneider Electric StruxureWare\Building Operation X.X\Enterprise Server\db\etc\server_startup.properties Increasing this threshold in server_startup.properties will allow the Enterprise Server to have a better chance of achieving a successful startup. server_startup.properties -- Original settings NspServer.Startup.Service.Status: fail NspServer.Startup.Service.Status.NbrOfConsecutiveFails: 2 NspServer.Startup.Service.Status.QuitRetryAfterNbrOfConsecutiveFails: 2 server_startup.properties -- Threshold increase to 10 retries. NspServer.Startup.Service.Status: success NspServer.Startup.Service.Status.NbrOfConsecutiveFails: 0 NspServer.Startup.Service.Status.QuitRetryAfterNbrOfConsecutiveFails: 10   Last option, and please go through all the previous steps mentioned before attempting: Open regedit and go to HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\Services\Building Operation X.X Enterprise Server. Open the DependOnService and remove the first line (netprofm) and then reboot. The ES will now start automatically.     Alternative Workarounds Go to Computer Management by right clicking on Computer and going to Manage. In Computer Management, go to Services and Application > Services > Building Operation X.X Enterprise Server. Right click on Building Operation X.X Enterprise Server and go to properties. The two different settings that can be changed so that the Enterprise Server starts automatically as a service after a reboot are as follows. Under the General tab, change the Startup type from Automatic to Automatic (Delayed Start). Or under the Recovery tab, change the Restart service after to a value of 3 or more minutes.

Issue Does EcoStruxure Building Operation support virtualization?  Can the Enterprise and Reports server be on a virtual machine? Can EcoStruxure Building Operation be installed in cloud environments? Product Line EcoStruxure Building Operation Environment VMWare Hyper-V Microsoft Azure Amazon Web Services EcoStruxure Building Operation 2.0 through current release. Cause Desire for virtualization or cloud environment. Resolution Emulating environments Virtualization has several interpretations. In this article, we'll specifically address running EcoStruxure Building Management software in emulating environments like VMware or Hyper-V. These emulating environment software packages replicate a physical PC environment, allowing multiple computers to operate on a single machine, hence the term "virtualization". Several software vendors offer emulating systems, with VMware and Hyper-V being the most prominent. The advantages of running an emulating environment include reduced physical machines, minimized space requirements, and lower maintenance costs.   It's important to note that other potential meanings of "virtualization" such as remote desktop, remote control software, terminal server environment, or cluster environment are not covered in this article.   EcoStruxure Building Management in emulating environments Currently, numerous installations are running EcoStruxure Building Management on VMware and Hyper-V without significant issues. Some challenges have been observed related to Veeam setup, which doesn't seem to integrate seamlessly with ES (and possibly EC).   VMware is utilized internally in R&D and Product Support teams with positive feedback on its performance. Users should have familiarity with the emulating product to configure settings correctly, ensuring network functionality. It's important to highlight that no specific efforts have been made to develop EcoStruxure Building Management to comply with emulating environments. Additionally, there are no specific tests to verify its functionality in emulating environments. Certain issues have been seen with the License system used by EcoStruxure Building Operation when running on specific emulating environments due to limitations in the license system's support for these environments.   Support for EcoStruxure Building Management installations running in emulating environments Product Support provides support for EcoStruxure Building Management software, irrespective of whether it runs on PC hardware or in an emulating environment. Support is provided for problems related to the EcoStruxure Building Management Software itself, but not for issues related to the environment it runs on. Except for approved operating systems and minimum memory requirements, Product Support does not offer guidance on configuring specific PC hardware or emulating environments. Cloud environments Cloud computing environments such as Microsoft Azure and Amazon Web Services provide on-demand availability of computer system resources without direct active management by the user. Cloud computing relies on sharing of resources and typically uses a pay-as-you-go model, which can help in reducing capital expenses.   One of the challenges of cloud computing is reduced visibility and control. Cloud users may not have full insight into how their cloud resources are managed, configured, or optimized by their providers. They may also have limited ability to customize or modify their cloud services according to their specific needs or preferences.   Support for EcoStruxure Building Management installations in Cloud environments EcoStruxure Building Operation has not been developed or tested with Cloud environments in mind and it is therefore not currently a supported environment.  

Issue There is no official internet download available for VisiSat documentation since the withdrawal of the Satchwell MicroNet and IAC products Product Line Satchwell MicroNet Environment Satchwell VisiSat Cause Documentation is no longer available for download. Resolution Further information and configuration details can be found in the following resources: VisiSat V1.2 Documentation Engineering Guide: Covers configuration for: IAC 400 IAC 420 IAC 600 IAC Touchscreen VisiSat V2.1 Documentation Engineering Guide (185 & 196 builds): Includes configuration for: MN300, MN440, MN500, MN620 MN350, MN450, MN550, MN650 MNLCD and MN Touchscreens Installation and User Guide Data Sheet Release Notes Attachments VisiSat V1.2 Engineering Guide.zip VisiSat V2.1 (185) Engineering Guide.zip VisiSat V2.1 (196) Engineering Guide.zip VisiSat 2.1 (196) Installation and User's Guide-0713.pdf VisiSat 2.1 (196) Data Sheet DS10202-0713.pdf VisiSat 2.1 (196) Release Note.pdf Related Articles MicroNet 100 Series Controller MLIs and Data Sheets MicroNet 50 Series Controller MLIs and Data Sheets Where can VisiSat software and license be purchased and what Version/Build is supplied?

Issue How to populate emailed event messages with specific event details. Product Line EcoStruxure Security Expert Environment Security Expert Server Cause Security Expert documentation is missing instructions on how to add specific object details to emailed event messages. Resolution 1. The following email tags can be inserted in the Message and Subject fields to dynamically populate the event email. <FIELDTIME> or <FIELD_TIME>   <EVENTID> or <EVENT_ID>   <LOGGEDTIME> or<LOGGED_TIME>   <FACILITYNUMBER> or <FACILITY_NUMBER>   <USERNAME> or <USER_NAME>   <CARDNUMBER> or <CARD_NUMBER>   <USERID> or <USER_ID>   <INSTRUCTIONS>   <DESCRIPTION>   <INSTRUCTIONS2> (second language)   <DESCRIPTION2> (second language)   <ALARM>   <COMMENTS>   <ACKNOWLEDGED>   <DOORNAME> or <DOOR_NAME>     2. Security Expert documentation is being modified to include this information on the email tags that can be used to populate email messages.

Issue I/A Series G3 Workbench unable to open platform for local host. Error indicates "Cannot display page. Workbench can only communicate with niagarad version 3 or higher." Environment I/A Series G3 Enterprise Network Server and Workbench (all versions) Cause The Niagara service for R2 is currently active. Resolution This error indicates the Niagara service for R2 is currently active. To correct, start the Niagara service for G3 by running the Install Niagara Daemon provided by the start menu for the G3 version required.

Issue When attempting to shut down the PC, the Sigma SUM application prompts for a password to close. Product Line Satchwell BAS & Sigma Environment Sigma SUM Cause Sigma SUM is designed to run continuously in the background. When the PC is shut down, the application requests a password to ensure controlled termination. Resolution To close the Sigma SUM application when prompted for a password, enter: Password: SUM Additional Recommendation: To avoid manual startup, add Sigma SUM to the PC’s startup programs so it launches automatically when the system boots.

Issue Field office needs to access the Web Service page so that they can perform an Ethernet network packet capture for communications troubleshooting purposes. Environment MNB-1000 with firmware 1.50E and earlier only. Cause Field office needs to access the Web Service page so that they can  perform an Ethernet network packet capture for communications troubleshooting purposes. Resolution The Web Service page has been removed from the MNB-1000 Plant Controller firmware effective with release version 1.510.  The user-name is user The password is mnb1000

Issue If the Xenta Server IP address is unknown or lost, how can the user retrieve or reset the IP address? Product Line Satchwell MicroNet, TAC INET, TAC Vista Environment Xenta Servers Xenta 511, 527, 555, 701, 711, 721, 731, 913 Cause Once the Xenta Server IP address is lost, the user has to use a serial connection cable to connect the Xenta Server to the HyperTerminal in order to retrieve the IP address. The serial cable is a RS-232 to RJ10 cable which can be purchase from Schneider Electric order entry (Part number: 00730920). For some reason, if the cable need to be home made, please follow the steps below to connect correct pins. Note: some third party IP search/scan software can be used to search all IP addresses in a range. User can also use this type of software to retrieve Xenta Server’s IP addresses. Resolution Xenta Server serial cable guide: Connect RJ10 pin 1 to RS232 pin 2. Connect RJ10 pin 2 to RS232 pin 3. Connect RJ10 pin 4 to RS232 pin 5. Connect RS232 pin 1, 6, 4 together. Refer to IP setup for a Xenta server (Xenta 5/7/9xx) through serial communication for how to set up HyperTerminal in order to retrieve/setup Xenta Server IP address.

Issue How to use AutoCAD layout in TGML Graphic Product Line TAC Vista Environment Vista 5.1.9 and earlier versions of Vista 5 TGML Graphic AutoCAD Cause Sometimes it is necessary to use the AutoCAD layout in TGML graphic, for example, to use the plant layout as a background. The official support for importing AutoCAD files was removed early in the life of TGML. It can’t be guaranteed that EVERY file will import without a problem, so it is an unsupported feature. Resolution The following steps need to be followed: Open the drawing in AutoCAD Save as .DXF Open TGML Editor File Open the .DXF A screen should pop up saying converting DXF to SVG followed by converting SVG to TGML It is recommended to use the "Create path" command in the Object window in TGML for the converted graphic. Because the response speed of the computer will be very slow if used without this action. Note: Line widths and text will be in disorder because they are not imported along with the object. If the DXF file fails to import, here are some steps to try: Move every object in AutoCAD to a single layer Delete all unused layers in AutoCAD "Explode" complex objects in AutoCAD

Issue Users need to determine the version or build number of the Sigma software installed on their system. Product Line Satchwell Sigma Environment Satchwell Sigma Cause Sigma software installations are identified by build numbers, not just release numbers. This can cause confusion when troubleshooting or verifying compatibility. Resolution To identify the Sigma release and build number: Open the Sigma Client on the Sigma Server. Navigate to Help > About System Manager. A window will display both the release number and build number. Reference Table Use the table below to match build numbers with their corresponding release versions and file dates. Sigma Release No. Build No. Software/Firmware File Date   SigmaX   Release 1 1.52 Software/Firmware 22.06.2001 SigmaX 4.5 Release 2 2.13 Software/Firmware 14.02.2002 SigmaX 5.2 Release 2 3.12 Supplement 14.02.2002 SigmaX 5.2 Release 3 3.12 Software 31.07.2002 SigmaX 5.2 Release 3.1 3.17 Software 17.09.2002 SigmaX 5.2 Release 3.3 3.3 Software 30.07.2003 SigmaX 5.2 Release 3.4 3.31.1 Software 03.10.2003 SigmaX 5.2 Release 3.6 3.32.10 Software 19.11.2003 SigmaX 5.2 Release 3.7 3.33.9 Software 22.12.2003 SigmaX 5.2 Release 3.7 SP2 3.33.11 Software 27.01.2004 SigmaX 5.2 Release 3.7 SP3 3.33.13 Software 19.02.2004 SigmaX 5.2 Release 3.10 3.34.11 Software 21.04.2004 SigmaX 5.2 Release 3.11 3.34.11 Supplement 31.08.2004 SigmaX 5.2 Release 4.00 3.36.11 Software 16.12.2005 SigmaX 6.0.1 Release 4.00 SP2 3.36.16 Software 02 03 2006 SigmaX 6.0.1 Release 4.00 SP4 3.36.20 Software 23.05.2006 SigmaX 6.0.1 Release 4.01 3.37.08 Software 07.09.2006 SigmaX 6.0.1 Release 4.01 SP1 3.37.09 Software 26 09 2006 SigmaX 6.0.1 Release 4.01 SP3 3.37.12 Software 20 10 2006 SigmaX 6.0.1 Release 4.01 SP4 3.37.13 Software 13 08 2006 SigmaX 6.0.1 Release 4.01 SP4a 3.37.16 Software 17 11 2006 SigmaX 6.0.1 Release 4.01 SP5 3.37.18 Software 05 01 2007 SigmaX 6.0.1 Release 4.02 3.39.09 Software 26 01 2007 SigmaX 6.0.1 Release 4.03 3.40.06 Software 06 06 2007 SigmaX 6.0.1 Release 4.03 Sp1 3.40.09 Software 09 08 2007 SigmaX 6.0.1 Release 4.04 3.41.14 Software 27.02.2008 SigmaX 6.0.1 Release 4.04 SP1 3.41.15 Software 09.05.2008 SigmaX 6.0.1 Release 4.04 SP2 3.41.16 Software 15 09 2008 SigmaX 6.0.1 Release 4.04 SP3 3.41.18 Software 08 01 2009 SigmaX 6.0.1 Release 4.04 SP4 3.41.19 Software 08 01 2009 SigmaX 6.0.1 Release 4.05 3.42.34 Software 06 11 2009 SigmaX 6.0.1 Release 4.05 SP1 3.42.43 Software 22 03 2010 SigmaX 6.0.2 Release 4.05 SP2 3.42.48 Software 26.08.2010 SigmaX 6.0.2 Release 4.05 SEB 3.43.18 Software 08 12 2010 SigmaX 6.0.2 Release 4.06 3.44.14 Software 01 12 2011 SigmaX 6.0.2 Release 4.06 SP1 3.44.16 Software 01 12 2011 SigmaX 6.0.2 Release 4.06 SP1 3.44.18 Hotfix 01 02 2012 SigmaX 6.0.2 Release 4.07 3 45 48 Software 20 08 2012 SigmaX 7.0.6 Release 4.07 SP1 3 45 51 Service Pack 09 12 2012 SigmaX 7.0.6 Release 4.07 SP2 3 45 58 Service Pack 20 12 2013 SigmaX 7.0.6 Release 4.08 3.46.57 Software 10 04 2014 SigmaX 7.0.7 Release 4.08 3.46.62 Hotfix 21.05.2014 SigmaX 7.0.7 Release 4.08 3.46.70 Hotfix 23 07 2014 SigmaX 7.0.7 Release 4.08 3.46.72 Hotfix 04 08 2014 SigmaX 7.0.7 Release 4.08 3.46.73 Hotfix 12 08 2014 SigmaX 7.0.7 Release 4.08 3.46.79 Hotfix 08 10 2014 SigmaX 7.0.7 Release 4.08 (**1) 3.46.80 Software 10 04 2014 SigmaX 7.0.7 Release 4.08 3.46.81 Hotfix 17 02 2015 SigmaX 7.0.7 Release 4.08 3.46.85 Hotfix 19 03 2015 SigmaX 7.0.7 Release 4.08 3.46.86 Hotfix 19 03 2015 SigmaX 7.0.7 Release 4.08 (**2) 3.46.89 Software 10 04 2014 SigmaX 7.0.7 Release 4.08 3.46.98 Hotfix 14 12 2016 SigmaX 7.0.7 Release 4.08 (**3) 3.46.104 Software 28 02 2017 SigmaX 7.0.9 Release 4.08 3.46.105 Hotfix 10 03 2017 SigmaX 7.0.9 Release 4.08 (**4) 3.46.106 Software 28 03 2017 SigmaX 7.0.9 Release 4.08 3.46.107 Hotfix 08 08 2017 SigmaX 7.0.9 Release 4.08 3.46.108 Hotfix 01 05 2018 SigmaX 7.0.9 Release 4.08 (**5) 3.46.110 Software 13 05 2019 SigmaX 7.0.9 Release 4.08 (**6) 3.46.111 Hotfix 15 11 2019 SigmaX 7.0.9 Release 4.08 (**7) 3.46.131 Software 29 01 2020 SigmaX 7.0.9 Notes:   **1 Sigma build 4.46.57 with StruxureWare Building Operation v1.5 or 1.6 transition support program installed. **2 Sigma build 4.46.57 with StruxureWare Building Operation v1.8 transition support program installed. **3 Sigma build 4.46.57 with StruxureWare Building Operation v1.9 transition support program installed. **4 Sigma build 3.46.57 with StruxureWare Building Operation v2.01 transition support program installed. **5 Sigma build 3.46.57 with StruxureWare Building Operation v3.0.1, v3.0.2 and v3.0.3 transition support program installed.. **6 Sigma build 3.46.57 with StruxureWare Building Operation v3.0.4, v3.1 and v3.2 transition support program installed. **7 Sigma build 3.46.57 with StruxureWare Building Operation v3.2 or later transition support program installed.   Notes: 1. SigmaX version 7.0.9 is now available and can be used on any Sigma version that supported SigmaX version 7.0.6. 2. This information can be downloaded as a PDF file: Sigma Build Numbers 2023 3. When SigmaX 6.0.2 is installed, the build information provided by Sigma (Help > About) can be wrong (later than the actual version). This arises because SigmaX installs a file with Build 3.42.47 in the c:\sigma\bin folder. This is only a problem prior to Sigma Release 4.05 SEB. ⚠️ Important Notice Sigma is not supported in EBO 2022 and later. To continue supporting Sigma devices, you can implement a multi-version system: Keep Enterprise Servers with Sigma devices on Building Operation 3.2. Add a Building Operation 2022 or later Enterprise Central Upgrade the rest of the system to Building Operation 2022 or later. You will not be able to upgrade EcoStruxure Building Operation servers that contain unsupported protocols, objects, or devices. Attempting to do so will result in failed upgrades or loss of functionality.