Notifications

We Value Your Feedback!
Could you please spare a few minutes to share your thoughts on Cloud Connected vs On-Premise Services. Your feedback can help us shape the future of services.
Learn more about the survey or Click here to Launch the survey
Schneider Electric Services Innovation Team!

Building Automation Knowledge Base

Schneider Electric Building Automation Knowledge Base is a self-service resource to answer all your questions about EcoStruxure Building suite, Andover Continuum, Satchwell, TAC…

Invite a Co-worker

Send a co-worker an invite to the portal.Just enter their email address and we'll connect them to register. After joining, they will belong to the same company.

Send Invite Cancel

Related Forums

Intelligent Devices Forum

Previous Next

Invite a Colleague

Found this content useful? Share it with a Colleague!

Invite a Colleague

Label: "tac inet"

View in: "Building Automation Knowledge Base" | Community

1458 Posts | First Used: 2018-09-06

Building Automation Knowledge Base

Issue Reset Instructions for 1200 Series SCU Product Line TAC INET Environment SCU 1200 series controllers I/NET Cause Need to restart SCU, perhaps after a reload of firmware or dip switch settings Resolution Follow the written instruction carefully. Reset Instructions: Locate the 3-pin connector labeled P610 and the reset push button switch. Refer to the above diagram. Momentarily short P610 pins 1 and 2 while simultaneously pressing the reset push button switch. (Note: P610 pins 1 and 2 are the pins located nearest the dip switch.) Re-download the proper BIN file to the SCU.

Issue I/NET Seven Rev 2.10 and IP Filtering Product Line TAC INET Environment I/NET site Cause IP Filtering on an I/NET Seven site with Rev 2.10 Resolution I/NET displays this summary when you select IP Filters from the I/NET Configuration Profiles editor. This summary lists each I/NET host that is currently communicating with this host workstation. Using IP filtering, you can configure each I/NET host to only see specific sections of the overall network. This allows you to create segmented networks that can be secured from outside access. I/NET displays this dialog when you highlight a device in the Device Filter Summary and select Modify. This dialog lists all filters currently defined for the selected device. IP filters are listed in order of their priority. The first IP filter in the list has the highest priority. The last IP filter in the list has the lowest priority. By default, a device will have a single IP Filter entry that allows the device to communicate without restriction.

Issue I/NET Seven and Key Card translation What is the Key / Card Translation table and how do I use it? Can I use the Key / Card Translation table for other card types other than I/DISC? Product Line TAC INET Environment I/NET all revisions Cause Need to understand what is the Key / Card Translation table and how do I use it. Resolution As I/NET evolved it first used what might be called a sequential look up table to translate I/DISC keys from number much to big for the DPU / SCU to interpret to one of the 1 to 24,000 (32,000 current) individual numbers permitted in a Tenant. The I/DISCs are shipped in lots from the manufacturer and the container states the starting key number, e.g. 897541, and the number of keys in the container. I/NET has an editor called Key / Card Translation that allows associating those I/DISCs with an individual. The box labeled Source is used to enter the first key/card in a lot of keys (usually read off the container). The Target box is used to assign the key to an individual in a Tenant. The Count box is used to set how many sequential keys will be associated with individuals. There are four card types that can be read directly without a translation table, Wiegand 26 and 32 bit and ABA 115 and 85. On the Wiegand cards the Tenant Code must match the site or tenant code on the cards and the card number must be less than 24,000. For all four types of card Switch 7 on the DPU is set to off. Wiegand 66 bit, Custom Wiegand and Custom ABA must be selected to use a translation table, and Switch 7 on the DPU is ignored. The next evolution involved allowing the “big (large) card number” to be stored with the Individual. This removes the requirement of using the key / card translation editor. Please see the following document for additional details and examples: Card Numbers.doc

Issue Have an I/NET System that has existing I/DISC that are listed in a Key / Card Translation table. The last bag of I/DISCs I received were un-sorted. How do I add these new I/DISC in the I/NET system? Want to enter the Individuals with new I/DISCs as large numbers Product Line TAC INET Environment I/NET all revisions Cause The manufacturer of the I/DISC is no longer supplying the I/DISC sorted. As such the range of the I/DISC can be outside the limit of 32,000 users per tenant as limited in I/NET. Resolution This is the process of adding NEW people in the system that has existing Key / Card Translation table and you want to enter the NEW Disk as large numbers. Please see the following document: Add Idisc.doc

Issue 7798C does communicate with a PC with either cable -- CBL082 or CBL072 Product Line TAC INET Environment I/NET Controllers including the 7798C Cause Improper Grounding Resolution There must be an earth ground connected to pin #3 of the 24 VAC power connector in order for communications to work correctly. Click on these pictures for a larger example: Note: Never use the shield as the ground. Grounding is accomplished by connecting a 14–18 AWG (2.081–0.897 mm2) wire from terminal 3 to true ground.

Issue Network Paging System or Network Wide SMS Messaging for I/NET Product Line TAC INET Environment I/NET Site Cause Requirement for Network Paging System or Network Wide SMS Messaging Resolution PageGate allows for network paging or network wide SMS messaging from any combination of the following modules: web, email, commandline/ascii, serial, TAP-in and (GUI) windows workstations. SMS or text messages can be sent to alphanumeric pagers, numeric pagers, cell phones, PIMs, billboards or pcmcia pager cards. For capturing and paging I/NET Seven alarms and messages we use the “Get Serial” module from PageGate. Please see the following link for Technical configuration and contact information: PageGate.doc To download the trial software please use the following website: https://www.notepage.net/ Expectations of Service Schneider Electric does not offer formal support for the third party software or hardware found here. Instead, our role is to provide a platform to provide information for people who want to take advantage of the global community of Schneider Electric customers. Schneider Electric will make every effort to monitor content to ensure the accuracy of the information you'll find, but any information provided by Schneider Electric staff is offered "as is" with no warranties, and no rights are conferred. You assume all risk for your use of third party software and hardware.

Issue TAC Xenta 527 - Embedded Web Server Product Line TAC INET, TAC Vista Environment I/NET Seven or Vista site Cause Need information concerning the TAC Xenta 527 - Embedded Web Server Resolution Information Technology Brief: The TAC Xenta® 527 is a web based presentation system for TAC Vista LONWORKS and I/NET Seven® networks. In addition, to supplementing the host workstation interface with web access, the TAC Xenta 527 can also be used as the sole operator interface into I/NET Seven and TAC Vista LONWORKS systems. A single Xenta 527 will handle small to midsized systems, and several devices can be used to handle larger networks. The web pages are based on standard Internet technology as HTML and Java™ Applets. Alarms can be forwarded as e-mail. Please use the following link: Xenta 527-23 June.doc

Issue ID Works 5.1 badge printing error and I/NET Seven rev 1.16B. Product Line TAC INET Environment ID Works 5.1 I/NET Seven rev 1.16B Cause Attempt to save or print a badge in ID Works 5.1, the following error occurs: Data Source Error A cursor with the name 'SQL_CUR06B8F1D0' already exists. State:37000,Native:16915,Origin:[Microsoft][ODBC SQL Server Driver][SQL Server] Resolution In order to correct this issue, contact Schneider Electric Product Support and ask for the “I/NET Seven 1.16B/IDW 5.1” patch. We will e-mail this patch to you. A better solution is to upgrade to I/NET Seven Rev. 1.17, which includes the patch in the software.

Issue How to configure Automatic DPU restore host functions? What is Automatic DPU Restore Host? Product Line TAC INET Environment I/NET Seven up to 1.15 to 2.10 Cause On larger I/NET Seven applications configured for File Equalization on building network backbones, it was found that temporary visitor badges and schedules were downloaded by multiple Hosts to multiple door controllers increasing network communications simultaneously caused this. By selecting a Primary Download Host (or a Secondary Download Host), I/NET can manage and assign responsibility for downloads concerning this information. Resolution Combining DPU Online Message Restores, DPU Memory Failure Restores and Temporary badges in the DPU Restore Host functionality, I/NET Seven more efficiently manages network traffic.. Please use the following white paper for configuration setup: Setting up Restore Host.doc For more detail please see customer advisor CA-2004-05.

To The Top!

Building Automation Knowledge Base

Related Forums

Intelligent Devices Forum

Remotely determine the MAC Address for an NPR or PC

Set up Custom Pin Numbers in I/NET Seven

I/NET Seven Upgrade Check List

Reset Instructions for 1200 Series SCU

I/NET Seven Rev 2.10 and IP Filtering

System Security and I/NET Seven with Windows XP

I/NET Seven custom installation/upgrade tips

I/NET Seven and Key Card translation

How to add new un-sorted I/DISC in the I/NET system?

Recover from a Software Restore on a new SCU replacing an existing DPU

Import Version 5.1 Sample.IWX from the I/NET Seven CD into ID Works 5.1

Convert ID Works Version 2.xx to run on I/NET Seven

Difference between the Indala/Motorola and HID/Dorado card readers.

7798C does not communicate with a PC or Sub-LAN

Network Paging System or Network Wide SMS Messaging.

PIN Pad functionality and I/NET Seven

TAC Xenta 527 - Embedded Web Server

ID Works 5.1 badge printing error and I/NET Seven rev 1.16B.

Configuring DPU restore host functions.

Reader wiring pin out for replacing a 7910 with a 7920 reusing the CAT 5 cable for the reader.

Building Automation Knowledge Base

Related Forums

This is a heading