Building Automation Knowledge Base

Issue How to bind BACnet Objects with Priority Levels Product Line EcoStruxure Building Operation Environment EcoStruxure Building Operation BACnet MPX, RPC, MPC Cause Servers (ES, AS) and other native devices (MPX, RPC) have slightly differing binding options. EcoStruxure Building Operation BACnet binding offers many options and the information below gives an example of how it can be achieved, it is not the only method. Resolution When binding between BACnet objects in EcoStruxure Building Operation (either external or within the device) it is usually better to utilize the BACnet Priority based control, often this facility is not fully exploited. Object Force and Overrides will use set priorities as in the BACnet Interface setting for the site (see System/Interface Manager/BACnet), the defaults are below. The example below shows a simple bind from a BACnet Schedule-value to a BACnet Binary-value Priority 16 (or other priority as required, as binding at Priority 16 can interfere with simple manual overrides). A BACnet datetime_value has no Priority array, so if you bind, for example, from a "BACnet Schedule Next transition" to "BACnet datetime_value Value" the bind to a Priority cannot be achieved, as below. In addition, the MPX & RPC have some constraints that Servers do not have. If you bind "Transfer Value to" an Object Value Property (rather than a Priority) then further bindings "Transfer Value to" binding to a Priority is inhibited. The screenshot below shows the error that is seen. This promotes using Priorities to control BACnet Objects.

Issue Unable to find Schlage Xdriver file on Exchange Download Center. Product Line Continuum Environment Xdriver add-on Cause It is unclear of where to download the Schlage Xdriver for Continuum.  Resolution All Schlage Xdriver .xdr files, as well as their accompanying documentation, can be found in the Schlage Wireless Lock Resources Kit on the Schneider Electric Exchange Download Center.

Issue When creating a BACnet trend log in an offline IP controller (e.g. an MP-C), the following properties are visible and can be adjusted: Delta Align intervals Interval offset Before download to the MP-C: After downloading to the MP-C these properties are not visible anymore. After download to the MP-C: Product Line EcoStruxure Building Operation Environment SmartX IP Controller Building Operation Workstation Cause Before downloading a “generic” object to a BACnet device, Workstation doesn’t know what BACnet properties the device supports and which it does not support. Therefore it will display the full super-set of BACnet properties for the given object type to the user. When the object has been downloaded, any property not supported by the device will be removed from the editor. Resolution This is by design.

Issue When viewing WebReports within WorkStation or Internet Explorer the report data is not shown. All that is seen is a blank screen even though the menu items are still displayed (as shown in Figure 1 below). Figure 1:: Report viewed through WorkStation (Or Internet Explorer) When viewing the same WebReport through a different browser, Chrome or Firefox the report displays correctly Figure 2:: WebReport viewed using other Browsers (such as Chrome and Firefox) Product Line EcoStruxure Building Operation Environment EcoStruxure Building Operation WebReports EcoStruxure Building Operation WorkStation Cause The issue has only been seen with Internet Explorer since the other browsers appear to work. Since Building Operation WorkStation uses Internet Explorer as its internal browser, the problem is seen when displaying WebReports within WorkStation. To confirm that this is the issue you can check the Windows Event Log contents (Application Log Warnings) related to: <Provider Name="ASP.NET x.x.xxxxxxx.x" /> ... <Data>/LM/W3SVC/1/ROOT/SchneiderElectric/WebReports-1-131958191596842252</Data> <Data>Full</Data> <Data>/SchneiderElectric/WebReports</Data> <Data>C:\Program Files (x86)\Schneider Electric EcoStruxure\Building Operation WebReports\WebReports\</Data> <Data>CultureNotFoundException</Data> <Data>Culture is not supported. Parameter name: culture 4096 (0x1000) is an invalid culture identifier. at System.Globalization.CultureInfo.InitializeFromCultureId(Int32 culture, Boolean useUserOverride) at Microsoft.Reporting.WebForms.ReportDataOperation..ctor(IReportServerConnectionProvider connectionProvider, Boolean requiresFullReportLoad) at Microsoft.Reporting.WebForms.HttpHandler.GetHandler(String operationType, IReportServerConnectionProvider connectionProvider) at Microsoft.Reporting.WebForms.HttpHandler.ProcessRequest(HttpContext context) at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStepImpl(IExecutionStep step) at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously)</Data> Resolution To correct this issue ensure that the Windows Regional Language, found in the Windows Control Panel matches between the Workstation PC and the Reports Server.

Issue Satchwell "AL..S" series Spring Return Linear Actuator requires replacement. Product Line Field Devices Environment Satchwell “AL..S” series Spring Return Linear Actuator installed on Satchwell MJF, MZ, MZF, VJF, VSF, VZ or VZF series Plug and Seat Valve Body.  Cause Obsolescence of Satchwell “AL..S” series Spring Return Linear Actuator. Resolution Replace Satchwell ALMS Actuator with S-E M700 Actuator. The S-E M700 Actuator may be used to replace an existing Satchwell ALMS Actuator. It should be noted however that the S-E M700 Actuator is suitable for use with 24 volt power supplies only, while the Satchwell ALMS Actuator is a mains voltage device. The S-E M700 Actuator has an average power consumption of 30 VA and the use of an independent 230 / 24 volt Transformer rated 50 VA is recommended.  S-E Transformer Type TR60 (341-3060-000)   Replacement of Satchwell ALXS Actuator with S-E M700 Actuator. The S-E M700 Actuator may be used to replace an existing Satchwell ALXS Actuator. It should be noted however that where an existing Satchwell ALXS Actuator has been connected to a Satchwell Climatronic Controller via an independent Transformer, it is probable that the Transformer will have been rated to provide the level of power required by a single ALXS Actuator (23VA) In such circumstances the existing independent Transformer may also require replacement by another independent Transformer, rated to provide the greater level of power required by a single S-E M700 Actuator (50VA) S-E Transformer Type TR60 (341-3060-000)   Replacement of Satchwell ALES Actuator with S-E M700 Actuator. The S-E M700 Actuator may be used to replace an existing Satchwell ALES Actuator. It should be noted however that where an existing Satchwell ALES Actuator has been connected to a Satchwell Climatronic Controller via an independent Transformer, it is probable that the Transformer will have been rated to provide the level of power required by a single ALES Actuator (26VA) In such circumstances the existing independent Transformer may also require replacement by another independent Transformer, rated to provide the greater level of power required by a single S-E M700 Actuator (50VA) S-E Transformer Type TR60 (341-3060-000)   Please check the latest catalog for current equipment.

Issue TAC Xenta I/O modules that are added as LonWorks units in TAC Vista, are converted to Xenta I/O modules belonging to a Xenta Base unit (SlaveSpeak devices) in EcoStruxure Building Operation, after conversion using TAC Vista Conversion Tool. Product Line EcoStruxure Building Operation, TAC Vista Environment Vista Server TAC Vista Conversion tool Xenta Xenta I/O-modules Cause In TAC Vista, the Xenta I/O modules are normally located on the same subnet as the Xenta Base unit, and belong to the Xenta Base unit, communicating as SlaveSpeak devices. If a Xenta I/O module is located on another subnet than the Xenta base unit, it could instead be added as a LonWorks Unit in Vista, and therefore communicating via LonWorks bindings to the Xenta base unit using SNVTs. Vista Conversion Tool does not handle this configuration. In the conversion tool, all Xenta I/O modules are expected to be connected directly to a Xenta base unit, located on the same Subnet, and are therefore always treated as SlaveSpeak devices. Resolution After running the Vista Conversion tool, you have to re-build the LonWorks Bindings between the Xenta I/O module and the Xenta Base unit manually in EBO, as the Conversion Tool does not handle the actual configuration setup.

Issue When an attempt is made to create or save a new schedule, you get the following error:       Product Line Access Expert Environment AccessXpert Hosted software v3 (all versions) AccessXpert Premise Software v3 (all versions) Cause Mercury has a limit of 255 schedules, which you can customize up to 254 schedules as there is the default "Always" schedule already built in. This is a limit on the Mercury hardware. Resolution It is highly encouraged customers to avoid utilizing all 255 unless absolutely necessary as you will run into the case below of not being able to add a new one should you need to (or a one-off). Folders, and all objects within them, apply towards the instance limitations. If there are 6 folders, ALL schedules in the folders plus the schedules in the instance all count towards your 255 limit.

Issue When editing an EBO graphic in Webstation rather than Workstation, there is an inherent feature which allows a user to zoom in and out of the graphic using the mouse scroll. They can also pan around the page by holding down the left mouse button as they move. In many cases however, this feature is not wanted and makes the graphic more difficult to use. Image Zoomed Out  Image Zoomed In and Panned Right Product Line Building Operation Webstation Environment Graphics Cause Pan and Zoom in Webstation are features that are enabled by default in all TGML Graphics Resolution Edit the graphic object and select the top TGML root of the page properties. There is a 'Disable Pan and Zoom' option which by default is set to False.  Setting this option to True and then saving turns off the Pan and Zoom functions for that graphic

Issue I/A Series G3 version 3.8 and N4 version 4.2 Weather Service not following redirects Product Line TAC IA Series Environment I/A Series G3 3.8.x I/A Series N4 version 4.2 or older  Cause The National Weather Service (NWS) started recently redirecting from an HTTPS to an HTTP connection. Current conditions are not updated in Weather Service. The following messages appear in station output:  TRACE [15:05:30 27-Feb-18 EST][weather] Redirect to https://www.weather.gov/xml/current_obs/KBIV.xml WARNING [15:05:30 27-Feb-18 EST] [weather] Updating current conditions failed for WeatherReport javax.baja.sys.BajaException: Unable to get NWS Current Conditions feed at com.tridium.weather.nws.NwsCurrentReader.getFeed(NwsCurrentReader.java:71) at com.tridium.weather.nws.NwsCurrentReader.getFeed(NwsCurrentReader.java:59) at com.tridium.weather.nws.NwsCurrentReader.getCurrent(NwsCurrentReader.java:84) at com.tridium.weather.nws.BNwsWeatherProvider.updateReport(BNwsWeatherProvider.java:630) at javax.baja.weather.BWeatherReport.doUpdateWeatherReport(BWeatherReport.java:275) at auto.javax_baja_weather_BWeatherReport.invoke(AutoGenerated) com.tridium.sys.schema.ComponentSlotMap.invoke(ComponentSlotMap.java:1602) at com.tridium.sys.engine.EngineUtil.doInvoke(EngineUtil.java:49) at javax.baja.sys.BComponent.doInvoke(BComponent.java:1135) at javax.baja.util.Invocation.run(Invocation.java:46) at javax.baja.util.Worker.process(Worker.java:166) at javax.baja.util.Worker$Processor.run(Worker.java:139) at java.lang.Thread.run(Thread.java:748) Caused by: java.io.IOException: Redirect URL same as requested URL: www.weather.gov/xml/current_obs/KBIV.xml at com.tridium.weather.nws.FeedReader.getFeed(FeedReader.java:60) at com.tridium.weather.nws.NwsCurrentReader.getFeed(NwsCurrentReader.java:67) ... 12 more java.io.IOException: Redirect URL same as requested URL: www.weather.gov/xml/current_obs/KBIV.xml at com.tridium.weather.nws.FeedReader.getFeed(FeedReader.java:60) at com.tridium.weather.nws.NwsCurrentReader.getFeed(NwsCurrentReader.java:67) at com.tridium.weather.nws.NwsCurrentReader.getFeed(NwsCurrentReader.java:59) at com.tridium.weather.nws.NwsCurrentReader.getCurrent(NwsCurrentReader.java:84) at com.tridium.weather.nws.BNwsWeatherProvider.updateReport(BNwsWeatherProvider.java:630) at javax.baja.weather.BWeatherReport.doUpdateWeatherReport(BWeatherReport.java:275) at auto.javax_baja_weather_BWeatherReport.invoke(AutoGenerated) at com.tridium.sys.schema.ComponentSlotMap.invoke(ComponentSlotMap.java:1602) at com.tridium.sys.engine.EngineUtil.doInvoke(EngineUtil.java:49) at javax.baja.sys.BComponent.doInvoke(BComponent.java:1135) at javax.baja.util.Invocation.run(Invocation.java:46) at javax.baja.util.Worker.process(Worker.java:166) at javax.baja.util.Worker$Processor.run(Worker.java:139) at java.lang.Thread.run(Thread.java:748) Note: The issue does not occur in I/A Series N4 version 4.3 or higher. Resolution For I/A Series G3 version 3.8 and newer, patched weather.jar modules resolve this issue. The weather module patches are available for download from the Schneider Electric Exchange as:  weather 3.8.311.1 - G3 Firmware weather 3.8.213.3 - G3 Firmware weather 3.8.112.1 - G3 Firmware weather 3.8.41.3 - G3 Firmware    To resolve the issue in Niagara 4.2 and/or versions of G3 not covered by the patches, Clear the hidden flag on the conditionsServer slot of the weather provider and change the value to w1.weather.gov.  After making this change, the current conditions will update.  The conditionsServer slot for each weather report will need to be modified if more than one is being used.  The following is a screenshot of the provider slot sheet. The Conditions Server slot is highlighted. Select Config Flags.   Config Flags dialog. Uncheck the Hidden flag and save.   View the Property Sheet for the provider and modify the Conditions Server to be w1.weather.gov

Issue Easy Lobby is compatible with limited Continuum versions Product Line Andover Continuum Environment Continuum Cyberstation Cause The Easy Lobby integration is developed and supported by HID. There has been no further development for integration amongst other revisions. Resolution Easy Lobby is only compatible with Continuum version 1.94 SP1.

Warning   Potential for Data Loss: The steps detailed in the resolution of this article may result in a loss of critical data if not performed properly. Before beginning these steps, make sure all important data is backed up in the event of data loss. If you are unsure or unfamiliar with any complex steps detailed in this article, please contact Product Support for assistance. Issue Issues upgrading Automation Servers (AS, AS-B, AS-P) connected to an Enterprise Server (ES) from versions prior to 2.0.x to a version that is 2.0.x. ES and one Automation Server will upgrade but no others connected to that same ES will upgrade and will show an error while attempting to download the new software.  Product Line EcoStruxure Building Operation Environment Building Operation Automation Server v1.9.x Building Operation Enterprise Server v1.9.x   Cause If the Automation Servers within the ES environment are not uniquely named, and/or are the same name as the ES, an error will be received if upgrade is attempted stating "Deploy upgraded database failed". Resolution As found within the Enterprise Central section of the 2.0 Release Notes, "All servers must have unique names".   *NOTE* Renaming the Automation Server will break any paths to that Automation Server, as such they will need to be corrected.   Follow these steps to address this issue: Prior to upgrading any devices within the environment, check for and find any servers with non-unique names Detach the Automation Server (with the naming identical to the ES or any other server) from the ES Rename the Automation Server with a unique name Correct any binding path issues Reconnect Automation Server to the ES Upgrade the environment to 2.0.x

Issue Copying objects from one MP-X device to another results in a validation error. "Property value '<object type>' already assigned"     Product Line MPx series EcoStruxure Building Operation Environment Building Operation Workstation Building Operation Multi-purpose Controller Building Operation Multi-purpose VAV Cause The Object ID is already used within the destination device Resolution This functions as design. To resolve this:   Manually enter the Object ID when creating files that may be copied to other MP-X devices. One may choose to use blocks of IDs up to 64,999.   2. Utilize the import/export function within EBO which will import the BACnet objects using the next available Instance IDs.

Issue Mobile Apps for Access Expert Product Line Access Expert Environment Access Expert site desiring the use of modern technology Cause Unable to find or know where to look for the Mobile Apps for Access Expert Resolution Based on the version of software using Version 2 (V2) or Version 3 (3) the apps are different for each, so please understand the differences. These can be downloaded from the app store on iOS devices.  For Version 2, there are three Mobile Apps depending on what is needed by the client, these are: Go to the App Store, click on Search and enter Keep and download the following apps Keep Monitor - which monitors what is taking place like the events on the system Keep Notify - which notifies the user via emails and texts if there is an Alarm that has been generated Keep Personnel - where existing users can be verified or picture updated etc For Version 3, there is only one Mobile App called Keep Mobile, this gives a general oversight of the system and what is going on with it. Go to the App Store, click on Search and enter Keep and download the following app Keep Mobile - which gives you the ability to see all users, events and Hardware that are configured on the system

EBO doesn't support save from controller for B3s

Issue When doing a conversion from TAC Vista with LNS Network, to EcoStruxure Building Operation, what system should handle the addressing of the devices? What does the Network property “Shared LNS and SBO network” mean? Product Line EcoStruxure Building Operation, TAC Vista Environment TAC Vista Conversion Tool Cause In a TAC Vista system, running as LNS system, the network is marked as Protected in TAC Vista. This means that all addressing is handled via the LNS system. Resolution After a conversion from TAC Vista with LNS network, to EcoStruxure Building Operation, a flag is set in the Network properties, named “Shared LNS and SBO network” which means that the LonWorks network is shared between LNS and EcoStruxure BMS. LNS is used for network management, such as handling addresses and Lon bindings. LNS has the ownership of the network. EcoStruxure Buildning Operation is used for downloading application and configuration to the controllers. It does not write in the address table of the Lon device.  This flag should not be set manually.

Issue The datasheet for DO-FA-12 says: Contact rating .......................250 VAC/30 VDC, 2 A, Pilot Duty (Power Factor 0.35) What does "Pilot Duty" mean? Product Line EcoStruxure Building Operation Environment Building Operation Automation Server Bundled (AS-B) Building Operation IO-module Cause The datasheet specifies the rating class of the relays.  Understanding what "Pilot Duty" means is needed in order to know what load can be controlled by the relay. Resolution A "Pilot Duty" rating means that this relay is made for a specific highly inductive load, such as controlling the coil of another relay or contactor. Contacts with a "Pilot Duty" rating have passed standardized testing to prove they can reliably control a "Pilot Duty" load. In another example the datasheet of a device may say: Relay contact rating 250 VAC / 30 VDC, 2 A Pilot Duty (C300) In this case C300 indicates the rating of the relay, according to the UL 508 standard. The start current of a motor could damages the relays in case the current is too high. The start current could be up to 8 times the rated current, or more.

Issue Setting up Visual Verification to track who has gained access to a door using Access Expert Product Line Access Expert Environment Access Expert v3 Cause Verification of access is a common feature request in access control integrations. The following steps show how to enable and access this feature within the Access Expert v3 product. Resolution Open and connect to the instance with the required credentials Select the Access Control Tab and click on the Visual Verification button Click on the Assign Reader button to Add the respective readers and click OK The Visual Verification Window opens up with the readers that were selected from the previous step on the right side of the screen. Select the necessary readers that will be used for the verification.                    Once someone scans a card on any of the selected readers, their saved image will then be displayed    *Note* If this Window is closed the configuration for Visual Verification will be lost and will need to be recreated

Issue With revision 1.0.37 and later, folders under the instance within the navigation tree are no longer there.   Product Line Access Expert Environment V3 Hosted Cause The 1.0.37 release of the Keep software removed the folders under the instance within Folder Explorer. Resolution Use the corresponding tabs at the top of the window.  

Issue Information concerning Linux releases used within the Automation Server.   Product Line EcoStruxure Building Operation Environment Linux Operating System (OS) Building Operation Automation Server Building Operation Automation Server Premium Cause Questions concerning Linux releases used within the Automation Server. Resolution AS versions to 1.4.1 run Linux kernel 2.6.25.1 AS versions 1.5 to 2.0.2 run Linux kernel 3.0.101 AS-P versions 1.7 to 2.0.2 run Linux kernel 3.5.0-lsp-3.3.1 For questions concerning what type of Linux...i.e. Red Hat, Ubuntu, openSUSE - There is no linux distribution in the automation server just vanilla linux kernel. For further reading, download some documentation about the kernel from their website www.kernel.org  

Issue Permissions on V3 Product Line Access Expert Environment Managing Permission settings for Individual Groups. Cause Limiting the Permission for users in accessing certain objects within the system for better management. Resolution Permissions can be configured for each user by following these steps: Open the API and connect to the respective instance with the relevant credentials Go to the General Configuration Tab Select the Groups Icon If creating a new Group, click the Add Group Button If modifying, select one from the list and double click to open it up Click on Add Permission and select the Object Type  Select the various check boxes to Grant or Deny access  Once completed then click on the Save & Close button to close the Editor