Hoang_Phu

Notifications

Ask Me About Webinar: Data Center Assets - Modeling, Cooling, and CFD Simulation
Join our 30-minute expert session on July 10, 2025 (9:00 AM & 5:00 PM CET), to explore Digital Twins, cooling simulations, and IT infrastructure modeling. Learn how to boost resiliency and plan power capacity effectively. Register now to secure your spot!

Invite a Co-worker

Send a co-worker an invite to the portal.Just enter their email address and we'll connect them to register. After joining, they will belong to the same company.

Send Invite Cancel

Hoàng Phủ

Ensign

‎2025-07-29

Company :

Nhan Kha

Latest Posts
Likes Given
Latest Contributions
Activity Feed

Hoang_Phu

Time syncronization citect scada

Guys, is it correct to set the IP address like this to synchronize the time of your SCADA system? I want to synchronize the time of the Scada system u...

Industrial Automation icon_circle Industry Automation and Control Forum

32 0 1

2025-07-27 02:32 AM

Hoang_Phu

No sending MCL file

Hello guys, I can't send the MCL file. How can I send it or do I need to update the firmware of this relay?This relay version 3.986332.0Easergy studio...

EcoStruxure Power & Grid icon_circle Protection & Control

50 0 2

2025-07-19 02:04 AM

Hoang_Phu

I can't read the circuit breaker value using the IEC-104 protocol with...

Hello guys, I can't read Double point with IEC-104 protocol, how to configure it? At this address 100, the breaker is Open (1) and the breaker is clos...

EcoStruxure Power & Grid icon_circle Protection & Control

37 0 0

2025-07-16 11:48 AM

Hoang_Phu

I cannot control a circuit breaker using the Micom 30x relay output.

I want to ask something. I have been using IEC61850 for a while. I want to read the IEC61850 CID file with T300 Rtu and control the breaker remotely. ...

EcoStruxure Power & Grid icon_circle Protection & Control

98 0 2

2025-06-28 04:34 AM

Hoang_Phu

PowerLogic T300 - Configuration to connect a "slave" IEC 61850 device

Hello engineers. I am new to HU250. If possible, please provide an example of adding a device to T300 using IEC 61850 protocol.

EcoStruxure Power & Grid icon_circle Protection & Control

280 0 3

2025-06-08 08:23 AM

Hoang_Phu

Power operation Analog data read

Hello guys, Im reading the line voltage value from the P3 relay. This value is more than 65535, so i cant read it. Please help me. How to adjust it?

Power Distribution IEC icon_circle Power Distribution and Digital Support

263 0 2

2025-04-10 09:15 AM

Hoang_Phu

How to configure Power Operation to read 64 bit values via modbus prot...

Hello guys, Im reading the line voltage value from the P3 relay. This value is more than 65535, so i cant read it. Please help me. How to adjust it?

EcoStruxure Power & Grid icon_circle Protection & Control

392 0 2

2025-03-30 04:51 AM

Hoang_Phu

PowerLogic T300 - When used as a slave IEC 104 device of ABB RTU, why ...

Hello guys, good day. I have a question for you all. I am reading the analog data of P5 relay from T300 rtu and sending it to ABB rtu via 104 protocol...

EcoStruxure Power & Grid icon_circle Protection & Control

475 2 3

2025-03-28 02:27 AM

Hoang_Phu

Micom P633

Hello guys, I am unable to read IEC61850 data from Micom P633 relay. If you have successfully read IEC61850 data from this relay, please share your ex...

EcoStruxure Power & Grid icon_circle Protection & Control

397 0 2

2025-03-11 02:34 AM

Hoang_Phu

Can I use the ion 7400 to make Disturbance Fault Recorder

Hello guys, I am thinking of using ION7400 to measure the time of a fault. Have you used it like this and is it possible? For example, is it possible ...

EcoStruxure Power & Grid icon_circle Metering & Power Quality

437 1 2

2025-02-20 07:58 PM

Hoang_Phu

PowerLogic T300 - How to read and transmit current measurement value f...

Hello guys, I'm just learning. I can't read the voltage value of the Easergy P3 relay. How can I read it? 110 000V Please help me. thank you

EcoStruxure Power & Grid icon_circle Protection & Control

459 0 2

2025-02-05 11:28 PM

To The Top!

Community Badges

This is a heading