Subscribing is a smart move!
You can subscribe to this forum after you log in or create your free account..
Welcome to the new Schneider Electric Community
It's your place to connect with experts and peers, get continuous support, and share knowledge.
- You may be familiar with Communities' brand new layout from SE.com.
- Don't forget to update your bookmarks and saved links with our new address (https://community.se.com/).
- If you encounter any issues, please contact SchneiderCommunity.Support@se.com.
Close
Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
since
Spock
BevanWeiss
since
Support for vendor data from DNP3
2021-10-11 12:24 PMWith more DNP3 device vendors supporting Device Attributes, but the limitation of the Device Attribute options starting to show itself, it would be nice if some of the other DNP3 object types were supported within Geo SCADA Expert. Additional support…View more
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
Database backup could save registry entries from ALL servers
2022-03-20 07:02 PMI'm not sure how feasible this is from a cyber security perspective.But we have customers with relatively large Geo SCADA Expert systems (i.e. with hot standby + 2 permanent standby servers).Whilst the database backup objects are good, because they c…View more
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
Ability to embed geospatial map into mimic
2020-09-11 12:12 AMWe often don't want the geospatial map to be the only view. It would be good if it was possible to embed such a map within an existing mimic.
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
Modbus driver - support for reduced cap on transfer sizes
2022-02-02 02:14 PMI was reminded of this issue that I've run into a couple of times with Geo SCADA Expert and certain Modbus devices. The best example is when using a Rockwell ControlLogix with a 1756-EN2T (for example). It's possible to write some custom logic to han…View more
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
M340/M580 reading Input Registers / Coils / Contacts (1, 10001, 30001 etc) using DTM Browser configuration
2019-12-09 09:22 PMHi all, We've recently tried to use the DTM Browser to communicate with a ModbusTCP device which has data available for reading on register 30001 upward, and data for writing to at 40001 and upward. I would have expected this to be a common situation…View more
Posted by: BevanWeiss in Modicon PAC Forum
Find more articles tagged with:
OPC-UA Driver
2021-03-09 01:48 PMI think it's time that Geo SCADA Expert got an OPC-UA driver to allow it to retrieve data from OPC-UA servers.
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
Fine-grained security for configuration permissions
2020-10-29 04:49 PMWe've recently had a customer encounter an issue which destabilised their Geo SCADA Expert system which I can't see a good way to easily overcome. The issue was: A user with configuration permissions to the database imported an SDE which should not h…View more
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
Embedded Query, add ability to sort by hidden column tied to visible column (i.e. for natural sorting of current value formatted)
2020-11-10 02:02 PMWe often use embedded query lists to present data, since they allow for a large amount of data to be presented, which easily accommodates the addition of new sites / information points to the list of data. One issue we have however, is that we want t…View more
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
Scaling for Delta Accumulators
2021-04-30 08:41 PMI've recently had a request for a customer for totalisers that have different units.So we have a DNP3 point which represents the daily total flow/production/consumption etc... which is in kL / kWhrs / kJ / Cats We then apply this through a set of Del…View more
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
More fine grained control over ViewX logging
2021-04-08 09:32 PMBy default the ViewX logging is quite excessive. Like it creates almost 7MB of log files to just open up a single mimic in an offline development system that I have.This results in performance issues since the logging appears to be synchronous to oth…View more
Posted by: BevanWeiss in EcoStruxure Geo SCADA Expert Ideas
Find more articles tagged with:
Create your free account or log in to subscribe to the forum - and gain access to more than 10,000+ support articles along with insights from experts and peers.