Subscribing is a smart move!
You can subscribe to this forum after you log in or create your free account..
Welcome to the new Schneider Electric Community
It's your place to connect with experts and peers, get continuous support, and share knowledge.
- Explore the new navigation for even easier access to your community.
- Bookmark and use our new, easy-to-remember address (community.se.com).
- Get ready for more content and an improved experience.
Contact SchneiderCommunity.Support@se.com if you have any questions.
Close
Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
since
Commander
enrgyautomation
Brahm Lategan
Company
Energy Automation Ltd
since
2022-02-01
Trained as a Controls PLC technician when I was a youngster, followed it up a B-Tech in Electrical Engineering. Nowadays, I pretend to hold a screwdriver, use copious amounts of WD40 and/or duct tape as the solution to fix everything! If that fails, hammer.
Com'X > Excel Web Query
2017-05-29 05:57 PMHello!Is it possible to pull data into MS Excel from a Com'X via Web Query?Thanks.
Posted by: enrgyautomation in Gateways and Energy Servers
Find more articles tagged with:
ION7650 Displaying negative kW
2018-11-30 06:41 AMHello All, I have 4 x ION7650s metering 11kV supplies. The meter displays negative kiloWatts when drawing a load from the grid. Is there a way to swap the CT polarity over in either the framework via PME Designer or in ION Setup? I am trying to avoid…View more
Posted by: enrgyautomation in Metering & Power Quality
Find more articles tagged with:
ION Setup v3.0: SEPAM Protection Relays
2018-11-22 03:16 AMHi All, I have circa 150ish SEPAMs of various models (S40, T40, S80, T80 etc etc) on a site, all wired on a Modbus RS485 to TCPIP network. Are the SEPAMs confgurable via ION Setup? I do not want access to the protection or trip settings, just basic i…View more
Posted by: enrgyautomation in Metering & Power Quality
A utility that can safely delete custom measurements from PME
2018-02-06 09:33 AMAdmit it. We've all done it... From beginners to pro's.Created a device via MDI / DTE / ETL and accidentally misspelled the register or quantity name....? Good luck.Forget to name the output of an Arithmetic module in VIP and you end up with somethin…View more
Posted by: enrgyautomation in Archives: Power Management Systems
Find more articles tagged with:
Com'X200 not showing all logged data values in .csv
2017-09-06 02:46 AMHello,I am logging flow temperature, return temperature, energy and volume flow to a Com'X200. This data is then published to a server via FTP. Logging is enabled in "Commissioning" as well as in "Device Settings", and I can see the device and all it…View more
Posted by: enrgyautomation in Gateways and Energy Servers
Find more articles tagged with:
Wireless m-bus mesh network solution
2017-05-14 04:01 AMHello 🙂This is a bit of a generic question and yes I am fishing for ideas!I have several Com'xs and Modbus gateways on a customer site with PMEv8.2 on a virtual server, all chugging along nicely.I am trying to collect the energy data from m-bus heat…View more
Posted by: enrgyautomation in Gateways and Energy Servers
Find more articles tagged with:
Com'X and FTPS
2017-06-13 06:28 PMHello!Can a Com'X publish logged data over FTPS via Port 22? If so, how?Thanks.
Posted by: enrgyautomation in Gateways and Energy Servers
Find more articles tagged with:
Com'X com port 1 static address wants DNS?
2017-05-16 04:59 PMHello!!Can anyone explain why, when one configures a static ip address to com port 1 on a Com'x, the config asks for a DNS address? It doesn't really make much sense.Thanks!
Posted by: enrgyautomation in Gateways and Energy Servers
Find more articles tagged with:
Create your free account or log in to subscribe to the forum - and gain access to more than 10,000+ support articles along with insights from experts and peers.