Subscribing is a smart move!
You can subscribe to this forum after you log in or create your free account..
Welcome to the new Schneider Electric Community
It's your place to connect with experts and peers, get continuous support, and share knowledge.
- Explore the new navigation for even easier access to your community.
- Bookmark and use our new, easy-to-remember address (community.se.com).
- Get ready for more content and an improved experience.
Contact SchneiderCommunity.Support@se.com if you have any questions.
Close
Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
since
Lt. Commander | EcoXpert Master
richard_schwass
since
2022-08-09
ION Meter - Rate of Change Module (High Speed)
2018-05-14 05:03 PMHi all,We are in need for a high-speed module in both intermediate and advanced ION meters to perform a rate-of-change calculation.Would need to be at least 50ms rate but ideally up to 1/2 cycle.The calculation would be: ROC (df/dt) = ( 2* fi+2 + fi+…View more
Posted by: richard_schwass in Archives: Power Management Systems
Find more articles tagged with:
Metering Harmonics beyond the 63rd
2018-04-29 05:43 PMHi all,We are increasingly getting requests for harmonic measurement beyond the 63rd harmonic. At least three separate customers in the last few months.The most recent use case was specifically for the 100th harmonic which is apparently a key diagnos…View more
Posted by: richard_schwass in Metering & Power Quality
Find more articles tagged with:
Detail relating to IEC61000-4-30 ION modules
2018-04-29 07:05 PMHi there, We are beginning to work with a customer to develop frameworks around the early warning diagnosis of feeder faults. This will center around monitoring of high-speed rolling voltages, currents and harmonics. It is clear to me that the 4-30 p…View more
Posted by: richard_schwass in Metering & Power Quality
Find more articles tagged with:
Rogowski Coils
2016-06-12 09:41 PMHi there,Do any of the metering offer work with Rogowski Coils?If not (as I suspect) are the intermediate devices that might be able to interface these to a current input?What about the 0-1volt option "F" on the ION7650 - would this work?Regards Rich…View more
Posted by: richard_schwass in Metering & Power Quality
Find more articles tagged with:
Badge Logo Incorrect on Partner Locator
2017-04-20 09:29 PMCould our badge be updated to the "Critical Power - Master" one which is our current certification on the Partner Locator page please:http://www.schneider-electric.com/en/locator/entitydetails.jsp?locale=WW_en1&header=se&locator=networking&poco=all&t…View more
Posted by: richard_schwass in Archives: Building Automation and Control
DNP Protocol for PM5560/5563
2016-06-09 07:02 PMHi there,I understand that this protocol was to be supported on the PM5560 / PM5563 devices. Is this already available in the latest firmware or still on the road-map. If not ready, when is it scheduled for? Will it be field upgrade-able.Regards Rich…View more
Posted by: richard_schwass in Metering & Power Quality
Find more articles tagged with:
PM8000 Accuracy of Frequency Measurements
2015-11-23 02:47 PMHi there,Could anyone clarify the specific accuracy figures of the PM8000 with respect to its standard-speed and high-speed frequency measurements?The technical datasheet refers to "Class 0.2 as per IEC 61557-12". Can this be expressed in more specif…View more
Posted by: richard_schwass in Metering & Power Quality
ION Pulser Module Strange Behavior
2015-08-27 02:57 PMHi there,We recently discovered strange behavior of the Pulser Module in an ION 7650 seemingly by-design.The PulseWidth register which you would expect is just used to define the width of the pulse also defines a delay prior to sending the pulse to t…View more
Posted by: richard_schwass in Metering & Power Quality
Find more articles tagged with:
ION Protocol support in Com'X 200 etc
2014-04-21 07:13 PMHi there,I would love to start a discussion on the merits of having ION protocol gateway support in the Com'X 200 and future gateway products.Too often we see EGX100/300s specified and sold to customers only to then be unable to integrate ION devices…View more
Posted by: richard_schwass in Gateways and Energy Servers
Find more articles tagged with:
User-based separation of Diagrams
2014-02-16 12:35 AMHi all,I would love to begin a market discussion of how many of us would need/use a PME system that could be segmented between user-groups.I.e. User 1 can see one set of diagrams/dashboards/reports/alarms and User 2 cannot see them but can see their …View more
Posted by: richard_schwass in Archives: Power Management Systems
Find more articles tagged with:
Create your free account or log in to subscribe to the forum - and gain access to more than 10,000+ support articles along with insights from experts and peers.