The Gateway software must run a minimum of version 1.18 to update to version 2.0 and newer. If your Gateway version is older than 1.18, contact support for assistance.   The Gateway 2.x releases support updates to device configuration in IT Expert. Device configuration is not available in IT Expert unless all the Gateways in your organization are updated to version 2.0 or newer including Gateways that are offline.       Gateway 2.1.1   December 2025   This release addresses an issue that prevented services from restarting after updating the software.   New features   This release will support video clips from NetBotz 75x surveillance cameras in IT Expert.   NetBotz 75x video clips are available on the Physical Security page in IT Expert when at least one of the Gateways in your organization is updated to version 2.1 or newer. NetBotz video clips in IT Expert   To retrieve NetBotz 75x video clips, you must first configure Web credentials in the Gateway on Device Communications page. More...       Updates   Information is shown in the discovery log for FTP, SCP, and NetBotz surveillance. The Gateway communication status sensor reports on FTP, SCP, and NetBotz surveillance.   Issues fixed   Gateway services restart as expected after updating the software. Devices no longer lose communication after updating the device library. Cascaded rack PDUs are rediscovered as expected after updating the device library. The Gateway auto-update installer time out was increased to prevent update failures. Device firmware updates are no longer erroneously reported in IT Expert as in progress. Timeout and retry settings are no longer reset to default values after a series of updates from versions older than 2.0. The Full name of the admin user can now be modified as expected. Gateway installations on Windows 11 now complete correctly. Gateway installations using the Linux GUI now complete as expected. Various security updates   Known issues   After manually updating the Gateway to version 2.1.1, a database migration failure warning message may be displayed. Up to 72 hours of sensor history data stored locally on the Gateway may no longer be available in the Gateway user interface. Sensor history is preserved in the EcoStruxure IT cloud and is available as expected in IT Expert. The Gateway will display sensor history again as new data is recorded.     EcoStruxure IT Gateway 2.1.0 no longer available   EcoStruxure IT Gateway version 2.1.0 is no longer available due to an issue restarting services after updating the software. We are working on resolving the issue and expect to release version 2.1.1 soon.   Customers who installed Gateway 2.1.0 can:   Wait until version 2.1.1 is released to update the software.   OR   Replace their Gateway with version 2.0.1 or 1.2.4 and then update the software when version 2.1.1 is released. How to replace your EcoStruxure IT Gateway with a new installation     Gateway 2.0.1 June 2025   This release addresses an issue that causes Gateway software updates to fail when the software is installed on Windows in a non-default directory.   It is not necessary to update Gateways running version 2.0.0 to version 2.0.1.   Gateway 2.0.0 March 2025   Updates   SNMPv3 device discovery now supports SHA-256 authentication type.   Instructions for setting up backups and in the SNMP walk tool were updated. Single dashes in commands - are now double dashes -- See How to create a device walk file for EcoStruxure IT Gateway Configure Gateway backup   Instructions for replacing the SSL self-signed certificate were updated. Paths in the installation directory have changed from .../gateway/conf/ to .../conf/ See How to replace the self-signed SSL certificate in EcoStruxure IT Gateway    Installing the WMIC utility on new Windows 11 systems before installing the Gateway is no longer required.   Known issues   After updating the Gateway to version 2.0.x, devices with no name can cause the communication between the Gateway and EcoStruxure IT to fail. Device discovery counts in the Gateway and IT Expert might not match, and alarm updates might not occur. Sensor measurements are maintained as expected. Note: ATS 5G devices with 1.x firmware are known to affect communication.   Update the ATS 5G device firmware to the latest 3.x version. Make sure the device name is set on the NMC device. Log in and go to Configuration > General > Identification. Populate the Name field if it is blank. Delete the device from the Gateway and discover it again.   See EcoStruxure IT Gateway known issues

The WMIC utility must be installed on new Windows 11 systems before you install EcoStruxure IT Gateway. Note: Older Windows 11 versions that were updated to 24H2 may already have WMIC installed. More...   Gateway 1.24.0 January 2025   This release includes:   SNMPv1 community strings are no longer displayed in the Communication > display or in logs. The Gateway detects failed software updates and rolls back to the previously installed version as expected. Relevant third party licenses are now in the License folder in the install directory. Devices reporting alarms can now be deleted as expected.

  The WMIC utility must be installed on new Windows 11 systems before you install EcoStruxure IT Gateway. Note: Older Windows 11 versions that were updated to 24H2 may already have WMIC installed. More...   Gateway 1.23.1 October 2024   Customers are encouraged to update their Gateway software to version 1.23.1. To receive Gateway software updates promptly, enable auto-update. See how...   This release replaces a certificate that enables device library updates. The Gateway must be at a minimum of version 1.23.1 to receive new device library updates. See How to update the Gateway device library   Important security updates   Gateway 1.23.0 September 2024   Two new state sensors Two new sensors are displayed on the device's details page IT Expert.   Gateway Communication Status - protocol   This sensor is available for every discovered device: SNMP, Modbus, NetBotz, Redfish. Example: Gateway communication status: NetBotz   Gateway File Transfer Status   This sensor is created when the communication protocol used by the device is available. Protocol settings must be configured and enabled on the device. Device communication settings configured on the Gateway and on the device must match. If settings don't match or communication settings are not configured on either the device or the Gateway, the sensor is not created. More...   IT Expert user configuration feature     This release supports the supports the APC NMC user configuration feature in IT Expert.   All the Gateways in your organization must be updated to at least version 1.23 to access this feature in IT Expert. More...     RHEL 7 and CentOS 7 not supported   A update of PostgreSQL prevents EcoStruxure IT Gateway version 1.23 and newer from being installed on CentOS 7 or RHEL 7. Attempts to update an existing Gateway to version 1.23 will fail.   For existing Gateway installations, deploy a new Gateway 1.23 on a supported Linux operating system. To retain sensor history, follow these instructions: How to replace your EcoStruxure IT Gateway with a new installation   Software vulnerabilities fixed in Gateway 1.23   The following third-party components were updated to address these specific cybersecurity vulnerabilities:   Apache CVE-2023-48795   PostgreSQL CVE-2024-7348   This release also includes various additional component updates to improve overall security.      

Gateway 1.22.1.5 July 2024   This release addresses an issue that prevented some customers from updating the Gateway software to 1.22.0. Software updates are now available for all customers.   Device credentials   The Device Credentials page now displays the number of devices using each configured credential.       

It is strongly recommended that you update your Gateway to the latest version. See how   Gateway 1.21.0   Gateway appliance   Gateway software updates, OS updates, or security updates are no longer deployed for the Gateway appliance. It is strongly advised that you migrate to a new installation of the Gateway software. How to replace your EcoStruxure IT Gateway with a new installation   Enhancements   A new Communication tab in the device details view displays information about device credentials for polling and file transfer.   This release updates Java to AdoptOpenJDK 17.0.9_0.   The following security vulnerability was addressed in this release: CVE-2024-0865 Schneider Electric Security Notification

  Get a quick overview of EcoStruxure IT Gateway known issues and fixes. If you’re experiencing issues not on this list, or if you have other feedback, please submit a request.     After manually updating the Gateway to version 2.1.1, a database migration failure warning message may be displayed. Up to 72 hours of sensor history data stored locally on the Gateway may no longer be available in the Gateway user interface. Sensor history is preserved in the EcoStruxure IT cloud and is available as expected in IT Expert. The Gateway will display sensor history again as new data is recorded.   During a Gateway software auto-update or an update manually initiated from IT Expert, the update status may erroneously be reported as failed while the update is still processing. Once the update has completed on the server running the Gateway, IT Expert will correctly show the updated Gateway version.   It is recommended that you wait 45-60 minutes for the update process to finish. If the Administration > Gateways page in IT Expert still reports a Gateway software update failure, click Retry update. Contact customer support for assistance if needed.   Attempting to discover an NMC-based device too soon after an NMC reboot can cause the device to report as Unknown or discover incorrectly. It is recommended to wait at least 1-2 minutes after a reboot before running a discovery.   After updating the Gateway to version 2.0.x, devices with no name can cause the communication between the Gateway and EcoStruxure IT to fail. Device discovery counts in the Gateway and IT Expert might not match, and alarm updates might not occur. Sensor measurements are maintained as expected. Note: ATS 5G devices with 1.x firmware are known to affect communication.   Update the ATS 5G device firmware to the latest 3.x version. Make sure the device name is set in NMC device. Log in and go to Configuration > General > Identification. Populate the Name field if it is blank. Delete the device from the Gateway and discover it again.   We are investigating reports of frequent communication alarms from NMC3 devices. More...   The .stage directory may be left behind during a backup. The backup is successful. The error displayed can be disregarded.   Gateway restore fails to execute when the locale is set to use Italian, Spanish, or Portuguese as the language. Change the locale to use English to perform the restore.   When a proxy server is configured on the Gateway, the files required for software auto update, appliance OS auto update, Device Library update, and firmware update are prevented from downloading. Until this issue is addressed in a future release: IT Expert Administrator users can download the latest Gateway software on the Administration > Gateways page and install it manually. Note: To update the software on a Gateway appliance, contact support for assistance.   Users with appropriate permissions can update device firmware directly on the device.   When a web browser on the server running the Gateway is left open for an extended time, polling timeouts due to intermittent high CPU and/or memory usage can occur. Close the browser to return system resources to expected levels.   The user running the Gateway Linux installer on RHEL or CentOS must have file system privileges set to umask 0022. Otherwise, the installer cannot initialize the database.   IT Expert does not receive configuration information for APC devices that were discovered in the Gateway before File Transfer Settings were specified. Make sure the File Transfer Settings in the Gateway are correct for the APC devices you want to discover, and then run the discovery again. Device data will be available in IT Expert after the next polling cycle completes.   A security update in Gateway requires that Redfish devices support 2048 bit server certificates. New Redfish discoveries can fail, and previously discovered Redfish devices may be listed as offline. To discover and monitor Redfish devices, install a new certificate on the Redfish device that supports 2048 bit server certificates.   Redfish discoveries can fail if SNMP is enabled on the device. Check whether SNMP is enabled on the device you want to discover, disable it, and try your Redfish discovery again.   Due to network latency, incomplete data might be displayed for a device, for example, the serial number is missing or sensors are not displayed. Check to see if there is a duplicate device in the Gateway device list that displays the correct values; if so, delete the device that displays incomplete information. If no duplicate device exists, check the network connection for the device, and then delete the device from the Gateway device list and rediscover it.   The Unsupported devices and Invalid device credentials lists cannot be modified or deleted from the Gateway user interface.   Login to the web page for a Galaxy VS UPS fails when you access it from the device details page in the Gateway. To access the device directly, type its IP address into a browser.   When the browser window is maximized, you cannot scroll in the Gateway device list when more than 20 devices are discovered. Reduce the size of the browser window for best results.   The SUMX v6.2.0 and v6.2.1 firmware is missing the OID that indicates the number of input phases. This is known to affect the Smart-UPS RT 20000 XL (3 phase UPS) and Symmetra LX 16000 RM (split phase UPS) but may affect others. Upgrade the firmware to either SUMX v6.4.0 or SUMX v6.5.0 to resolve the issue. Get the latest firmware here. For more information see this APC FAQ.   TrippLite UPS models SMART100RM1U and SMART750RM1U can show a negative Battery Temperature reading, for example, -13.89 C. Update the firmware on your devices to resolve this issue.   NetBotz 200 does not display the temperature correctly when the temperature preference is set to Fahrenheit on the device. You can log in to the NetBotz 200 and change the temperature preference to Celcius in the Administration > General > Preferences option.   The serial number does not update in the Gateway when a power module is replaced in a Symmetra PX. Rediscover the Symmetra PX to display the information for new power modules as expected. Do not remove the Symmetra from the Devices list.   The Gateway installer does not open ports in the firewall to allow access to the web server. You must access the Gateway application from the local host. You can access the application from remote hosts only if you disable the firewall on your computer.   Automatically detecting proxy server settings fails in some environments. You can manually configure your proxy server settings. See Installing and setting up EcoStruxure IT  

How to update the Gateway device library   Note: Gateway device library releases update the device library only, not the Gateway software. See the EcoStruxure IT Gateway release notes   Device Library v3.1.0.10 (Included with IT Gateway 2.1.1 Release)   December 2025   New device support (Vendor, Series, Type, Protocol)   Crouzet, XM05, CRAC, Modbus Eaton, SC300, Rectifier, SNMP Innovative Circuit Technology (ICT), Modular Power Series, UPS, SNMP Updated devices   Chatsworth, eConnect PDU (Previous Model/Legacy), RPDU, SNMP Add -1 check to probeHumidity and also remove unnecessary scaling. Eaton, EPDU, Rack PDU, SNMP Fix discovery issue on "G4" Series Generac, Power Zone Pro, Generator Control Module, Modbus Remove "Generator Stopped" as an alarm. Alarm is always active when genset is not operating. "Generator Stopped Due To Alarm" should cover unexpected stops. Uniflair/Schneider Electric, SP/WM/MB Telecom SIG Series, CRAC, Modbus Fix 32-bit values being read in the incorrect byte order. Various, PPC-UPS MIB, UPS, SNMP Fix discovery issue on some devices using PPC-UPS MIB (EPPC-MIB) Various, UPSMIB, UPS, SNMP Add attributes for Firmware Revision, UPS Agent Software Version, and MAC Address. Ignore Battery Temperature value of 999 Update device "Name" attribute to try using upsIdentName (.1.3.6.1.2.1.33.1.1.5.0) first and fallback to sysName (.1.3.6.1.2.1.1.5.0) if needed.   Device Library v3.0.0.604 July 2025   New device support (Vendor, Series, Type, Protocol)   Vertiv, ITA2, UPS, SNMP Updated devices   APC/Schneider Electric, Devices with APC NMC, Various, SNMP MAC address attribute has been added to all APC/SE devices that are equipped with an APC/SE NMC. ASCO, G5 Group Controller, ATS, Modbus DEVICE TYPE HAS CHANGED AND WILL CAUSE PREVIOUSLY DISCOVERED DEVICES TO GO OFFLINE. THERE WILL BE LOSS OF HISTORICAL DATA AND REDISCOVERY WILL BE REQUIRED Expand sensor support and fix various errors Various, PPC UPS (Upsmate.mib), UPS, SNMP Update discovery protocol to prevent UPSs that only support a few PPC UPS OIDs from using this DDF instead of the UPS-MIB (RFC 1628) DDF. Various, UPS MIB (RFC 1628), UPS, SNMP Expand validation test to prevent N/A sensors from displaying.  PowerLogic, HeatTag, Environmental Monitor Probe, Modbus Fix bug causing "Unknown" status for Air Quality Index   Device Library v3.0.0.597 June 2025   Updated devices   Schneider Electric, PowerTag, Power Meter, Modbus Update lookup table for device model Fix incorrect Modbus register definitions for Voltage Phase-N Rittal, Kelvin Chiller (pCO5+), Chiller, SNMP Add MAC Address attribute   Device Library v2.0.0.572 (IT Gateway 1.24.x)/v3.0.0.591 (IT Gateway 2.0.x) May 2025   New device support (Vendor, Series, Type, Protocol)   Schneider Electric, Easergy PS100, Power Supply, Modbus Updated devices   APC by Schneider Electric, Various, UPS, SNMP Add sensor support for Power Cabinet Ambient Temperature and Switchgear Ambient Temperature Carel, IR33, CRAC, Modbus Various fixes for reported issues with sensor values Wagner, OxyReduct M-Line, Environmental Monitor, Modbus Fix incorrectly defined Modbus function codes   Device Library v2.0.0.570 March 2025   New device support (Vendor, Series, Type, Protocol   Cummins, ModLon II Gateway, Generator Control Module, Modbus   Device Library v2.0.0.569 March 2025   Updated devices   APC by Schneider Electric, NetShelter Rack PDU Advanced 10000 Series, RPDU, SNMP Fix alarm message bug Schneider Electric, Easy Cooling Row, Cooling Device, Modbus Fix incorrect Model and Serial Number values   Device Library v2.0.0.566 February 2025   New device support (Vendor, Series, Type, Protocol   Schneider Electric, Galaxy Li-ion Battery Cabinet Advanced, Battery Manager, Modbus Updated devices   Uniflair by Schneider Electric, LEL Series, Cooling Device, SNMP Expand sensor support for latest firmware Uniflair by Schneider Electric, TSA/TRA Series, Chiller, SNMP Expand sensor support for latest firmware   Device Library v2.0.0.559 January 2025   New device support (Vendor, Series, Type, Protocol   Huawei, Various, UPS, SNMP UPS devices that support HUAWEI_UPS_MIB SNMP OIDs (.1.3.6.1.4.1.2011.6.174.x). Updated devices   Tripp Lite, WEBCARDLX Devices, Various, SNMP Fix bug causing alarms to not appear in ITE. Wagner, OxyReduct M-Line, Environmental Monitor, Modbus Fix "Identifier" attribute that was incorrectly labeled "Serial Number".   Device Library v2.0.0.554 January 2025   New device support (Vendor, Series, Type, Protocol   AVTech, RoomAlert 3S, EMS, SNMP Updated devices   APC by Schneider Electric, Various UPS, SNMP Add check for "not applicable" value on Battery Temperature Add support for Battery Pack component on Easy UPS devices equipped with SE NMC Uniflair by Schneider Electric, LE Series - TDCVx/TUCVx, SNMP Add missing sensors and remove sensors that are not applicable to these models   Device Library v2.0.0.548 November 2024   New device support (Vendor, Series, Type, Protocol   ABB, CMS600, Branch Circuit Monitor, Modbus Alltec, Leak Detector, Environmental Monitor, Modbus IMARI, UFM-700 Series, Generic Device (Flow Meter), Modbus Vertiv/Liebert, MiniMate3, CRAC, SNMP Wagner, OxyReduct M-Line, Environmental Monitor, Modbus Updated devices   Cisco, Various, Network Switch, SNMP Remove "Interface {0} : Down" alarms to prevent inaccurate alarm states during discovery. These will be reimplemented once there is a way to prevent intentionally unoccupied ports from alarming during discovery. PowerLogic, HeatTag, Environmental Monitor Probe, Modbus Update alarm severities   Device Library v2.0.0.542 October 2024   New device support (Vendor, Series, Type, Protocol   RC Group, Next EVO INV, CRAC, SNMP Updated devices   APC by Schneider Electric, Various UPS, SNMP Add missing environmental components/sensors. (Easy UPS with NMC) Fix bug causing missing Input Contact from populating.   Device Library v2.0.0.534 October 2024   New device support (Vendor, Series, Type, Protocol   Rittal, RiMatrix S, Chiller, SNMP Generac, Power Zone Pro, Generator Control Module, Modbus Updated devices   APC,  RPDU2, RPDU, SNMP Add power factor to Power - Bank calculation. Previous calculation was apparent power (VA). MGE, STS, SNMP Fix 6.55 MW power spike bug cause by device firmware bug. MIB-2, SNMP Fix Device Uptime sensor value scaling.   Device Library v2.0.0.523 September 2024   Updated devices   2BM, Nemo 72, RPDU, Modbus Fix incorrect byte order for reading sensor values.   Device Library v2.0.0.515 August 2024   New device support (Vendor, Series, Type, Protocol)   CoolIT/Cooltera, CHx750/FS400, CRAC, SNMP The CoolIT CHx750 and Cooltera FS400 devices use the same SNMP MIB and OIDs. These devices will use the same DDF. Updated devices   APC by Schneider Electric, NetShelter 10000 Series, RPDU, SNMP Fix bug where alarm severity does not update when an active alarm's severity increases or decreases in severity. APC by Schneider Electric, ATS5G, ATS, SNMP Fix missing/incorrect AOS and App Version attributes Schneider Electric, Amico, CRAC, SNMP Fix missing/incorrect AOS and App Version attributes Schneider Electric, TSA/TRA, Chiller, SNMP Fix missing/incorrect AOS and App Version attributes   Device Library v2.0.0.511 July 2024   New device support (Vendor, Series, Type, Protocol)   Intesis, Fujitsu RAC/VRF Gateway, CRAC, Modbus Stulz, WallAir, CRAC, SNMP Updated devices   Stulz, CyberAir 3PRO, CRAC, Modbus Update Modbus register data type to float Uniflair/Schneider Electric, SP/WM/MB Telecom SIG Series, CRAC, Modbus & SNMP Update alarm severities   Device Library v2.0.0.505 June 2024   New device support (Vendor, Series, Type, Protocol)   2BM, Nemo 72, RPDU, Modbus Cummins, ProtoNode, Generator Control Module, Modbus Supports 1 Generator and 1 ATS   Device Library v2.0.0.498 June 2024   Updated devices   APC/Schneider Electric, Various, SNMP Add an uptime sensor to the NMC component. APC/Schneider Electric, Modular PDU, PDU, SNMP Update OIDs used for Model, Serial Number, Application Version, and AOS Version attributes. Liebert/Vertiv, Various, SNMP Update alarm severities.   Device Library v2.0.0.489 April 2024   New device support (Vendor, Series, Type, Protocol)   Liebert/Vertiv, PMP v4 for STS2/PDU, PDU, SNMP Updated devices   Uniflair, ERAx/ISAx/Aquascroll, Chiller, Modbus/SNMP Update alarm severities.   Device Library v2.0.0.484 April 2024   New device support (Vendor, Series, Type, Protocol)   Clivet, WSAx-YES, Chiller, Modbus Schneider Electric, EM6000H Series, Power Meter, Modbus Stulz, CyberAir 3PRO, CRAC, Modbus Updated devices   Uniflair, LE L, CRAC, SNMP Updates to support latest firmware.   Device Library v2.0.0.477 March 2024   New device support (Vendor, Series, Type, Protocol)   CyberPower, Various, ATS, SNMP There are ATS devices that discover as RPDUs because they use "ePDU/ePDU2" OIDs instead of "ats" OIDs from the CyberPower SNMP MIB. A DDF was added to fix the incorrect device type. If you have one of these devices discovered as an RPDU, the device will need to be deleted and rediscovered so that the correct device type displays. This will cause historical data loss. Updated devices   Cummins, PowerCommand 80, ATS, Modbus Add checks for "Out of Range" sensor values. Various, PPC UPS (Upsmate.mib), UPS, SNMP Fix incorrect values for Apparent Power sensors that are being calculated. This update impacts Schneider Electric Easy UPS devices that use the E3SOPT001 network cards. Uniflair, BREx/Aquascrew, Chiller, Modbus/SNMP Update alarm severities. Uniflair, FanWall, CRAC, SNMP Various updates for new/updated sensors on latest firmware. Various, UPSMIB, UPS, SNMP Add phase count check to Input Voltage sensor to prevent Phase 2 and 3 values from displaying on single phase devices.   Device Library v2.0.0.472 March 2024   New device support (Vendor, Series, Type, Protocol)   Hager, JKM01, Power Meter, Modbus Updated devices   Schneider Electric, Easy Cooling XDCV, CRAC, Modbus Alarm severity updates Sensor label updates   Device Library v2.0.0.469 February 2024   New device support (Vendor, Series, Type, Protocol)   Cummins, PowerCommand 80, ATS, Modbus Rolls Royce, MTU Kinetic Power Pack, Generator Control Module, Modbus   Updated devices   Schneider Electric, Various, UPS, SNMP Add Time Since Last Diagnostic Test sensor Fix "Phase null" sensor labels on Galaxy VS devices Schneider Electric, EcoStruxure BMS BACS (previously Gutor BMS BACS), Modbus/SNMP Update model name from "Gutor BMS BACS" to "EcoStruxure BMS BACS" Expand alarm support Update some alarm strings and severities Vertiv/Liebert, Various, SNMP Expand alarm support using latest LGP MIB Stulz, WIB8000, Cooling Devices, SNMP Expand sensor support for CRACs and chillers   Device Library v2.0.0.465 January 2024   Updated devices   Mitsubishi, UPS, SNMP Fix blank device manufacturer field Add fix to prevent invalid battery temperature reading from displaying   Device Library v2.0.0.463 December 2023   Updated devices   Liebert/Vertiv, Various, SNMP Fix discovery issue on multiple devices with the same LGP Agent serial number   Device Library v2.0.0.456 November 2023 New device support (Vendor, Series, Type, Protocol)   RLE Technologies, WiNG MGR DS, Environmental Monitor, SNMP Schneider Electric, TOPDSP800, UPS, SNMP Updated devices   Schneider Electric, PowerChute Network Shutdown, Server, SNMP Fix discovery issue Woodward, DTSC-200, ATS, Modbus Modbus read optimizations   Device Library v2.0.0.450 October 2023 New device support (Vendor, Series, Type, Protocol) Uniflair/Schneider Electric, SP/WM/MB Telecom SIG Series, CRAC, Modbus & SNMP Updated devices Schneider Electric, Easy Cooling XDCV, CRAC, Modbus Fix Modbus register offset Vertiv/Liebert, Static Transfer Switch 2, Transfer Switch, SNMP Expand sensor support   Device Library v2.0.0.440 September 2023   New device support (Vendor, Series, Type, Protocol) Uniflair/Schneider Electric, FWCV, CRAC, SNMP   Updated devices APC by Schneider Electric, NetShelter Rack PDU, RPDU, SNMP Fix blank Name attribute  APC by Schneider Electric, Gen 2 Rack PDUs, RPDU, SNMP Add per phase Power Factor sensor Cisco, Various, Network Switch, SNMP Expand alarm support Fix missing Model on some devices Fix missing Serial Number on some devices Phoenix Contact, QUINT4 DC UPS, UPS, Modbus Fix Serial Number issue Schneider Electric, Easy Cooling XDCV, CRAC, Modbus Various updates from latest Modbus register map   Device Library v2.0.0.426 July 2023   New device support (Vendor, Series, Type, Protocol) Schneider Electric, Easy UPS 3S, UPS, Modbus Vertiv, CR, CRAC, SNMP Vertiv, CRD010, CRAC, SNMP   Updated devices Rittal, LCP (with pCOWeb card), Chiller, SNMP Fix scaling on some sensor values   Device Library v2.0.0.418 June 2023   New device support (Vendor, Series, Type, Protocol)   APC by Schneider Electric, Environmental Management System (legacy), Environmental Monitor, SNMP Phoenix Contact, QUINT4 DC UPS, UPS, Modbus Synaccess Networks Inc., SynLink RPDU, RPDU, SNMP Vertiv, PowerSure Interactive 5 UPS, UPS, SNMP   Updated devices   APC by Schneider Electric, SmartUPS Ultra, UPS, SNMP Fix missing outlet group sensors HW-group (HWg), STE and STE2, Environmental Monitor Probe, SNMP Use sysName as default for name attribute Juniper, Various, Network Switch, SNMP Use sysName as default for name attribute Oracle, RMII Enhanced PDU, RPDU, SNMP Fix threshold alarm bug Server Technology Inc. (ServerTech), Sentry4, Rack PDU, SNMP Add Unified ID support Sinetica, Hawk-i2, Monitoring Unit, SNMP Use sysName as default for name attribute   Device Library v2.0.0.409 May 2023   New device support (Vendor, Series, Type, Protocol)   APC by Schneider Electric, ACRC100 Series, CRAC, Modbus APC by Schneider Electric, ACRC300 Series, CRAC, Modbus Rittal, LCP (with pCOWeb card), Chiller, SNMP   Updated devices   APC by Schneider Electric, ATS5G, ATS, SNMP Fix environmental sensor validation Fix sensor value scaling for Humidity APC by Schneider Electric, NetShelter Rack PDU, RPDU, SNMP Add support for environmental probes Bard, LC6000, CRAC, Modbus Additional value scaling fixes Riello, Netman 204 (network card), UPS, SNMP Additional source for user-defined device name Various, UPSMIB, UPS, SNMP Fix device names displaying "none"   Device Library v2.0.0.403 April 2023   New device support (Vendor, Series, Type, Protocol)   HW-group (HWg), STE2, Environmental Monitor Probe, SNMP PowerLogic, HeatTag, Environmental Monitor Probe, Modbus Schneider Electric, Easy UPS SRV, UPS, Modbus Vertiv/Liebert, PMP v4 for RDC, Power Meter, SNMP   Updated devices   Bard, LC6000, CRAC, Modbus Fix bug preventing unit conversions from occurring PowerLogic, Thermal Tag TH110, Environmental Monitor Probe, Modbus Add missing parameters and other improvements Various Redfish improvements   Device Library v2.0.0.394 March 2023   New device support (Vendor, Series, Type, Protocol)   Bard, LC6000, CRAC, Modbus For Modbus register list from manual version 7960-791G Juniper, Various, Network Switch, SNMP   Updated devices   Schneider Electric, iEM3000 Series, Power Meter, Modbus Fix alarm bug Rittal, CMC-TC, Monitoring System, SNMP Fix device name attribute Schneider Electric, Gutor BMS BACS, Battery Management System, SNMP Fix missing battery modules Cisco, Various, Network Switch, SNMP Expand sensor support   Device Library v2.0.0.382 February 2023   New device support (Vendor, Series, Type, Protocol)   Lenovo, XCC BMC, Server, Redfish   Updated devices   CyberPower, Smart App Series, UPS, SNMP Fix device discovery bug Rittal, CMC-TC, Monitoring System, SNMP Fix missing units on some sensor values Add support for "Battery Health Alarm Sleep Time" and "Battery Health Alarm Warning Time" parameters Uniflair by Schneider Electric, Various, Modbus/SNMP Alarm severity updates   Device Library v2.0.0.372 December 2022   New device support (Vendor, Series, Type, Protocol) ComAp, InteliLite NT MRS, Generator Control Module, Modbus Cummins, PowerCommand 500 Series (ATS), ATS, Modbus Fronius, Symo Hybrid, Inverter, Modbus Generac, D100 H-Panel, Generator Control Module, Modbus Proges Plus, Sensor Net Connect (POI0010), Environmental Monitor, SNMP Schneider Electric, iEM3000 Series, Power Meter, Modbus Schneider Electric, VarPlus Logic VL6, Power Meter, Modbus Schneider Electric, Vigilohm IM400, Insulation Monitoring Device (implemented as "generic" device in IT Gateway/IT Expert), Modbus Uniflair by Schneider Electric, Uniflair LE Direct Expansion (Gen 2), CRAC, Modbus Uniflair by Schneider Electric, Uniflair AM SDCx/SUCx (with Carel pCOC/MP20II), CRAC, Modbus Updated devices APC by Schneider Electric, Smart-UPS (SUMX), UPS, SNMP Add support for "Battery Health Alarm Sleep Time" and "Battery Health Alarm Warning Time" parameters APC by Schneider Electric, APC SmartUPS (SMT/SMX/SURTD/SRT), UPS, Modbus Expand alarm support Add support for UPS Efficiency and Efficiency Status parameters Cisco, Various, Network Switch, SNMP Fix a bug where portions of some sensor names display as "null" Schneider Electric, Easy UPS 3M, UPS, Modbus Remove "Inverter Supply Power" alarm and reimplement as a state sensor instead Vertiv/Liebert, Various, SNMP When lgpConditionType OID returns "alarm" or "fault" and lgpConditionSeverity OID returns "not-applicable", we will report the alarm severity as a critical instead of informational Device Library v2.0.0.348 November 2022 New device support (Vendor, Series, Type, Protocol) Rittal, CMC-TC, Monitoring System, SNMP APC by Schneider Electric, UPS, Modbus Galaxy VL 200/500 kW Galaxy VS/PX 10-100 kW Symmetra PX 20-160 kVA (NMC2 firmware application sy3p and px2 v6.5.0+) Symmetra PX 250/500 kVA Basler, DGC-2020 (non-legacy), Generator Control Module, Modbus DGC-500/DGC-1000 upgrade/replacement Updated devices APC by Schneider Electric, NetShelter 10000 Series, RPDU, SNMP Fix breaker Load State and Current sensor issue Liebert/Vertiv, MPH/MPHR/MPX, RPDU, SNMP Add daisy chaining support Expand Unified ID support PowerLogic by Schneider Electric, ION9000 Series, Power Meter Update various sensor names and groups SICES, GC310, Generator Control Module, Modbus Fix Engine Coolant Temperature value scaling Device Library v2.0.0.334 November 2022 New device support (Vendor, Series, Type, Protocol) SICES, GC310, Generator Control Module, Modbus Updated devices APC by Schneider Electric, NetShelter 10000 Series, RPDU, SNMP For discovered devices, there will be loss of historical data on breaker and switched outlet sensors due to necessary updates to add Network Port Sharing (NPS) support Add support for metered outlet measurements and alarms Fix discovery failure while using Network Port Sharing feature Fix labels that returned as hexadecimal strings Various, Modbus/SNMP Update unique identifiers incorrectly reporting as "Serial Number" to be "Identifier" instead Device Library v2.0.0.328 October 2022 New device support (Vendor, Series, Type, Protocol) Redetec, PN/3.0/Red/FAL, Fire Suppression System, Modbus Uniflair by Schneider Electric, Uniflair Room Cooling (Gen2), CRAC, SNMP Updated devices Schneider Electric, Easy UPS 3M, UPS, Modbus Registers defined for the following parameters were corrected: Serial Number Firmware Version Air Filter Maintenance Cycle (Month) Air Filter Maintenance Time Battery Running Time Luminous/Various, Various, UPS, SNMP Various fixes to improve data quality This SNMP MIB is used by multiple vendors. This change affects devices that use the following OID tree: .1.3.6.1.4.1.43943.1.1 Device Library v2.0.0.311 September 2022 New device support (Vendor, Series, Type, Protocol) Schneider Electric, Easy UPS 3M, UPS, Modbus Schneider Electric, Galaxy PW, UPS, Modbus For devices using JBus/Modbus Communication Card Schneider Electric, Galaxy VM (3:3 50-225kVA 400/480V), UPS, Modbus Schneider Electric, EVlink EV Charger, EV Charger, Modbus Device Library v2.0.0.305 September 2022 New device support (Vendor, Series, Type, Protocol) ASCO, Power Manager Xp 7000 Series, Power Meter, Modbus Circutor, CVM-NRG96, Power Meter, Modbus Cummins, PowerCommand 500 Series, Generator Control Module, Modbus CyberPower, Switched/Metered ATS, ATS, SNMP Uniflair by Schneider Electric, Various, CRAC, SNMP Support added for the following devices equipped with Carel pCOWeb communication cards utilizing "custom OID" firmware: Uniflair AM SDCx/SUCx with pCO1 and UG40 Uniflair AM SDxx/SUxx with pCO1 and UG40 Uniflair LE TDCV/TUCV with pCO1 and UG40 Uniflair LE Txxxxx11/Txxxxx21/Txxxxx22/Txxxxx42 with pCO1 and UG40 Updated devices Cisco, Various, Network Switch, SNMP Add port-level sensors Riello, NetMan 204, UPS, SNMP Add a fallback for the UPS name attribute Tripp Lite, WEBCARDLX Devices, Various, SNMP Fix discovery failure on devices not reporting a serial number over SNMP For devices using PowerAlert 20.x.x firmware, make sure you have a "Monitor" role set up under "SNMP Users". For more information, please refer to the PowerAlert Device Manager (PADM) 20.0.0 User's Guide Device Library v2.0.0.288 August 2022 New device support (Vendor, Series, Type, Protocol) FG Wilson, PowerWizard 2.x/3.x, Generator Control Module, Modbus Liebert/Vertiv, XDC Chiller and Pumping Unit, Chiller, SNMP Updated devices APC by Schneider Electric, SmartUPS, UPS, Modbus Fix incorrect Battery Age Caterpillar, EMCP4, Generator Control Module, Modbus Added alarm support Device Library v2.0.0.277 July 2022 New device support (Vendor, Series, Type, Protocol) Raritan, PX iPDU, RPDU, SNMP Liebert/Vertiv, Challenger Cooling System, CRAC, SNMP Soler & Palau (S&P), DOMEO 210 FL 3V EU, Heat Recovery Unit, Modbus Schleifenbauer/Daxten, hPDU, RPDU, SNMP Updated devices Liebert/Vertiv, MPX Rack PDU, RPDU, SNMP Add support for environmental sensor Fix sensor mapping bug in IT Expert for environmental sensors Eaton, Various, UPS, SNMP Fix a bug where some devices discover, but present no sensors Uniflair by Schneider Electric, Various, CRAC/Chiller, SNMP/Modbus Alarm severity updates Tripp Lite, SNMPWEBCARD, RPDU/UPS, SNMP Expand Unified ID support NetBotz by Schneider Electric, NetBotz 250, Environmental Monitor, SNMP Add 0-5v sensor support Device Library v2.0.0.264 June 2022 New device support (Vendor, Series, Type, Protocol) Carrier, AquaSnap, Chiller, Modbus Liebert/Vertiv, PPC Distribution Cabinet, PDU, SNMP Liebert/Vertiv, PDX/PCW Large CRAC, CRAC, SNMP Nortec, Humidifier, Generic, Modbus Schneider Electric, EcoBreeze, CRAC, Modbus Sensatronics, Model U Universal Monitor, Environmental Monitor, SNMP Uniflair by Schneider Electric, Various, CRAC/Chiller, SNMP Support added for the following devices equipped with Carel pCOWeb communication cards utilizing "custom OID" firmware: LRACx/LRAHx with Carel pCOXS BRRCx/BRWCx/BRWHx with Carel pCO1 and MP20II BRECx/BREFx with pCO1 and MP20II BRACx/BRAFx/BRAMx/BRATx with pCO1 and MP20II BCWCx with pCO3 and UG50 BCECx/BCEFx with pCO5 and UG50 Updated devices APC by Schneider Electric, InfraStruxure PDU, PDU, SNMP Add ITA support for circuit meter breakers Liebert/Vertiv, Rack PDU 2, RPDU, SNMP Add support for environmental sensors Device Library v1.14.0.62 Requires EcoStruxure IT Gateway version 1.14 May 2022 New device support (Vendor, Series, Type, Protocol) CyberPower, Smart App Series, UPS, SNMP Riello, Netman 204, UPS/ATS/STS, SNMP Tripp Lite, SR(X) COOL, CRAC, SNMP Updated devices APC by Schneider Electric, Easy UPS 3S/3M, UPS, SNMP Add Battery Temperature sensor APC by Schneider Electric, PowerChute Network Shutdown, Software, SNMP Various improvements APC by Schneider Electric, Various Smart-UPS, UPS, SNMP Modify Output Total Percent Load and Output Total Percent Power sensor labels to include measurement units Add Output Efficiency sensor occurring under certain discovery conditions Improvement for devices equipped with battery string/block monitoring Add sensor for Time Since Last Battery Replace APC by Schneider Electric, Remote Power Panel (RPP), PDU, SNMP Add Hardware Revision attribute Application Version attribute being reported as Firmware Version APC by Schneider Electric, NetShelter Rack PDU, RPDU, SNMP Various improvements APC by Schneider Electric, InRow RD 100 Series, CRAC, SNMP Add attributes for Firmware Version and Hardware Version Dell, Server, Redfish Various improvements NetBotz by Schneider Electric, NetBotz 750, Environmental Monitor, SNMP Added 0-5v sensors NetBotz by Schneider Electric, NetBotz 250, Environmental Monitor, SNMP Added new sensors NetBotz by Schneider Electric, NetBotz 200, Environmental Monitor, SNMP Fix temperature sensor scaling Samsung/Schneider Electric, Samsung BMS/Schneider Electric Lithium Ion Batteries, BMS, Modbus Various improvements Device Library v1.14.0.46 Requires EcoStruxure IT Gateway version 1.14 April 2022 New device support (Vendor, Series, Type, Protocol) Liebert/Vertiv, Liebert NX/SX - Chloride ManageUPS Net Adapter, UPS, Modbus Eaton, ATC-900, ATS, Modbus Updated devices CyberPower, ePDU, RPDU, SNMP Add environmental sensor support Uniflair, Various, CRAC/Chiller, SNMP Add sensor validation check for "-858993460" to all sensors Device Library v1.14.0.40 Requires EcoStruxure IT Gateway version 1.14 March 2022 New device support (Vendor, Series, Type, Protocol) Carel, IR33, CRAC, Modbus Legrand, Various, UPS, Modbus Support added for the following models: Daker DK/Daker DK Plus Keor LP/Keor S/Keor Line RT Dhea Whad 800-2500/Whad CAB Megaline Niky/Niky S Updated devices APC by Schneider Electric, NetShelter RPDU, RPDU, SNMP Remove invalid "Power - Bank" sensors APC by Schneider Electric, Power Management Module (PMM), SNMP Add support for "Input Max Instantaneous Neutral Current" parameter APC by Schneider Electric, Various SmartUPS, UPS, SNMP Add support for "Battery Health Alarm Warning Time" and "Battery Health Alarm Sleep Time" parameters Add support for "High Transfer Voltage" and "Low Transfer Voltage" thresholds Add support for "Time Since Input Energy Usage Timer Last Reset" parameter Rename "Time Since Last Timer Reset" parameter to "Time Since Output Energy Usage Timer Last Reset" Deep Sea Electronics, DSE72xx/DSE61xx/DSE74xx, Generator Control Module, Modbus Convert "Warning Alarm Active" alarm to a state sensor and remove alarm Fix "Control Unit Failure" alarm bug PowerLogic, Power Meter, PM5000 Series, Modbus Various updates and bug fixes Device Library v1.14.0.30 Requires EcoStruxure IT Gateway version 1.14 March 2022 New device support (Vendor, Series, Type, Protocol) Woodward, DTSC-200, Automatic Transfer Switch (ATS), Modbus Updated devices APC by Schneider Electric, Various SmartUPS, UPS, SNMP Add Lower/Upper Output Voltage Tolerance sensors Resolved issue related to Number of External Battery Packs and and Number of Battery Cabinets sensors Add Output Voltage sensor to some devices APC by Schneider Electric, Remote Power Panel (RPP)/Power Management Module (PMM), SNMP Resolved issue related to Circuit Alarm Generation and Circuit Breaker State sensors APC by Schneider Electric, NetBotz 250, Environmental Monitor, SNMP Use high precision pod probe temperature when available Samsung/Schneider Electric, Battery Manager, Modbus Various alarm updates Resolved issue related to Cell Temperature scaling Device Library v1.14.0.19 Requires EcoStruxure IT Gateway version 1.14 February 2022 Updated devices APC by Schneider Electric, SmartUPS, UPS, SNMP Fix incorrect Output Voltage scaling on some devices Fix incorrect state on System Status sensor Fix log spam on devices that have Battery Packs/Cartridges Device Library v1.14.0.16 Requires EcoStruxure IT Gateway version 1.14 February 2022 New device support (Vendor, Series, Type, Protocol) Advance Cooling Systems (ACS), Panel Air Conditioner, CRAC, Modbus Hewlett Packard Enterprise (HPE), PDU3, RPDU, SNMP Vertiv, APM, UPS, Modbus Updated devices APC by Schneider Electric, Gen 2 RPDU, RPDU, SNMP Add per-phase sensors for Load State and Peak Current APC by Schneider Electric, Micro Data Center, Micro Data Center, SNMP Remove power meter sensors returning "-1" for values Remove UPS sensors returning "-1" for values Eaton, Powerware UPS, UPS, SNMP Add attributes for Firmware Revision and SKU Fix missing serial number attribute on some devices Update alarm severities Add network card component Gutor by Schneider Electric, Gutor SDC, Charger/Rectifier, SNMP Add new state for "Output Status" Uniflair by Schneider Electric, Various, CRAC, SNMP & Modbus Fix ITA related bug for "Run Hours" sensors Vertiv, Various, Various, SNMP Expand ITA support Fix missing "System Output Power Phase" sensors on NX225-600k UPS's and add ITA support for those sensors Device Library v1.13.0.53 Requires EcoStruxure IT Gateway version 1.13 January 2022 New device support (Vendor, Series, Type, Protocol) MGE, Upsilon, STS, Modbus Eltek, Smartpack S/Smartpack2, Controller, SNMP Panduit, G5 iPDU, RPDU, SNMP General Electric (GE), LP Series UPS, UPS, SNMP Elcos, Various, Generator Control Module, Modbus Schneider Electric, Com’X 510, Gateway, Modbus APC by Schneider Electric, SmartUPS Ultra, UPS, SNMP Updated devices APC by Schneider Electric, Various, UPS, SNMP Fix Battery Age sensors that report a default value of 01/01/2000 Fix missing Time On Battery sensor Remove redundant Battery Check Recommended warning event Fix scaling for Time Running On Battery on some devices Fix phase nomenclature on Galaxy VS devices APC by Schneider Electric, Rack PDU Gen 2, RPDU, SNMP Add Location attribute Fix incorrect/missing Apparent Power data on daisy-chained devices APC by Schneider Electric, Micro DC, Micro Data Center, SNMP Fix bug where Application Version and AOS Version attributes did not update in ITE after updating the firmware APC by Schneider Electric, Power Management Module (PMM), PDU, SNMP Fix bug where Firmware Version and AOS Version attributes did not update in ITE after updating the firmware APC by Schneider Electric, NetBotz 250, Environmental Monitor, SNMP Fix missing Pod Door Sensor Uniflair by Schneider Electric, TSAx/TRAx with 7-inch touchscreen, Chiller, SNMP Fix Compressor 2 Output sensor label displaying as duplicate Compressor 1 Output sensor Geist, Upgradeable/R-Series v5.0 PDU, RPDU, SNMP Fix bug where all outlet names were “Outlet 2” Device Library v1.13.0.33 Requires EcoStruxure IT Gateway version 1.13 December 2021 New device support (Vendor, Series, Type, Protocol) APC by Schneider Electric, ATS5G, ATS, SNMP Dell, iDRAC (iDRAC-SMIv2 MIB), Server, SNMP Uniflair by Schneider Electric, XRAC/XRAF, Chiller, Modbus Updated devices Uniflair by Schneider Electric, ERAx/ERCx pCO1/MP20II, Chiller, SNMP/Modbus Add fan type to all "Unit Type" sensor enumerations APC by Schneider Electric, Microlink, UPS, SNMP Add support for Battery Pack sensors Samsung/Schneider Electric, Samsung BMS/Schneider Electric Lithium Ion Batteries, BMS, Modbus Add support for cell level sensors APC by Schneider Electric, NetBotz Rack Monitor 200/250, Environmental Monitor, SNMP Extend ITA support to wireless probes Device Library v1.13.0.26 Requires EcoStruxure IT Gateway version 1.13 December 2021 New device support (Vendor, Series, Type, Protocol) Alpha Technologies, Cordex CXC, System Controller, SNMP Caterpillar, EMCP 4, Generator Control Module, Modbus Delta Energy Systems, PSC 1000, System Controller, SNMP Schneider Electric, PowerChute Network Shutdown (PCNS), UPS Management, SNMP Socomec, STATYS XS, Transfer Switch, SNMP Updated devices APC, SmartUPS (various), UPS, SNMP Fix bugs related to Output Voltage, Output Current, Output Active Power, and Output Total Apparent Power Fix Output Active Power returning -1 Liebert/Vertiv, Power Management Panel (PMPv4), Power Meter, SNMP Support for additional models Monico, mCore SDR, Generator Control Module, Modbus Add support for second generator Make -1 the default "invalid" value Raritan, PDU2, Rack PDU, SNMP Fix errors spamming console log Schneider Electric, Easy PDU ("EPDU" SKU), Rack PDU, SNMP Various bug fixes Schneider Electric, Easy UPS 3PH, UPS, SNMP Add 3-phase Output Apparent Power, Total Output Apparent Power, and Total Output Apparent Power Percentage measurements with support for ITA Server Technology Inc. (ServerTech), Sentry4, Rack PDU, SNMP Various bug fixes Uniflair by Schneider Electric, InRow RD (ACRD600), CRAC, SNMP Add Return Humidity sensor Add Humidifier Water Conductivity sensor Device Library v1.13.0.13 Requires EcoStruxure IT Gateway version 1.13 November 2021 New device support (Vendor, Series, Type, Protocol) Liebert/Vertiv, Power Management Panel (PMPv4), Power Meter, SNMP Monico, mCore SDR, Generator Control Module, Modbus PowerLogic by Schneider Electric, PM800 Series (using PM8ECC communication module), Power Meter, SNMP PowerLogic by Schneider Electric, HDPM, BCM, SNMP PowerLogic by Schneider Electric, BCMP (3-Phase), BCM, Modbus Socomec, Delphys GP, UPS, SNMP Vertiv, Netsure Rectifier, Rectifier, SNMP Updated devices APC, Smart-UPS, UPS, SNMP Fix Output Efficiency returning negative percentage values Fix some devices that are missing Input Phase Count/Output Phase Count attributes APC, Various CRACs/Chillers, CRAC/Chiller, SNMP - Fix scaling issues on some sensors Liebert, Various, Various, SNMP - Fix "Info" level alarms reporting as "Critical" Various, UPSMIB, UPS, SNMP - Add a fallback for missing name and/or model attributes on some devices Device Library v1.12.0.14 Requires EcoStruxure IT Gateway version 1.12 October 2021 New device support (Vendor, Series, Type, Protocol) Black Box, AlertWerks ServSensor, Environmental Monitor, SNMP Tripp Lite, WEBCARDLX UPS, UPS, SNMP Uniflair/Schneider Electric, XRAC/XRAF, Chiller, SNMP Uptime Devices, Sensor Hub, Environmental Monitor, SNMP Updated devices Airedale, EasiCool EZRE Precision Air Conditioning (DF35X-EZRE-1, pCOWeb), CRAC, SNMP Add "Unit Status" sensor Remove "General Alarm" APC, Smart-UPS, UPS, SNMP - Fix Output Frequency sensor returning "-" instead of frequency measurement. Cisco, Various, Network Switch, SNMP Change device type from "generic" to "ip switch" Add firmware version attribute Add chassisMinorAlarm/chassisMajorAlarm/chassisTempAlarm as alarms Eaton, EMS-PDU, RPDU, SNMP - Fix discovery issue with PXGX PDP Eaton, Powerware UPS, UPS, SNMP - Fix scaling issue on Input Power - Phase # sensor for some devices Schneider Electric, NetBotz 750, SNMP - Add firmware version attribute Various, Various, UPS, SNMP - Codified "Battery Age" and "UPS Age" on numerous devices to better support analytics. Device Library v1.12.0.4 Requires EcoStruxure IT Gateway version 1.12 September 2021 New device support (Vendor, Series, Type, Protocol) Uniflair/Schneider Electric, XRAC/XRAF, Chiller, SNMP APC/Schneider Electric, Easy RPDU Gen. 2 (MBO/SMBO), RPDU, SNMP Emerson/Liebert/Vertiv, GXT4, UPS, SNMP Emerson/Liebert/Vertiv, GXT5, UPS, SNMP Emerson/Liebert/Vertiv, NX225k-600k, UPS, SNMP Updated devices APC/Schneider Electric, Easy UPS, UPS, SNMP - Fix unsupported Battery Current sensors returning 32767/-32767 APC/Schneider Electric, InfraStruXure PDU (xPDU), PDU, SNMP - Add support for Breaker Panel Energy Usage and Power sensors. Uniflair/Schneider Electric, Uniflair LE L, CRAC, SNMP - Add support for Actual Speed Fan 1-4 sensors APC/Schneider Electric, Various, UPS, SNMP Remove sensors that return "-1" Modify Battery Block sensor names to include its associated Battery String Square D, MicroLogic, Breaker, Modbus - Remove sensors that return "-32768" APC/Schneider Electric, Modular PDU (MPDU), PDU, SNMP - Add support for Input Contacts and Output Relays PowerLogic, PM53xx, Power Meter, Modbus Add Apparent Energy and Reactive Energy Delivered +/- Received sensors Various fixes Device Library v1.11.0.21 Requires EcoStruxure IT Gateway version 1.11 September 2021 IMPORTANT: If you have a Modbus device that has been discovered with Type: UPS, Vendor: MGE, Family: MgeGalaxyUps you will need to rediscover the device with the following: Type: UPS, Vendor: MGE, Family: mgeGalaxy_300_7000   New device support (Vendor, Series, Type, Protocol) APC/Schneider Electric/MGE, Galaxy 5000/5500, UPS, Modbus Uniflair/Schneider Electric, AquaCentr Gen 2 (Model BCW* with NMC), Chiller, SNMP Uniflair/Schneider Electric, "Telnew" (MB/SP/WM) with custom OID 99053, CRAC, SNMP This is for Uniflair MB/SP/WM devices equipped with a Carel pCO1 web card and UG40 HMI using the custom enterprise OID "99053" instead of the standard Carel enterprise number "9839". Komfovent, Verso-CF, CRAC, Modbus CyberPower, ePDU, RPDU, SNMP Eaton, Rack Monitor (v2.00), Environmental Monitor, SNMP Updated devices APC/Schneider Electric, Easy UPS, UPS, SNMP - Fix missing serial number attribute on some models APC/Schneider Electric, ACRD 300 Series, CRAC, SNMP - Fix Delta-T Setpoint sensor Various, PPC UPS (Upsmate.mib), UPS, SNMP - Add Battery Age sensor. This is for devices/vendors that use the "Upsmate" SNMP MIB, which includes many Easy UPSs Emerson/Liebert/Vertiv, eXM M/S/R, UPS, SNMP - Fix missing temperature sensors/alarms Emerson/Liebert/Vertiv, Various, Various, SNMP - Support for newest models added to the lgpProductSpecific OID table Emerson/Liebert/Vertiv, Various, Various, SNMP - Update default alarm severity for alarms that cannot be mapped properly Grundfos, CIM 500, Pump, Modbus Fixed register offset issue Fix scaling for temperature sensors Add check for invalid sensors (value of 65535) Chatsworth, eConnect PDU (Previous Model/Legacy), RPDU, SNMP - Now reads the name attribute when it does not use the user-defined name. Device Library v1.11.0.3 Requires EcoStruxure IT Gateway version 1.11 August 2021 New device support (Vendor, Series, Type, Protocol) APC/Schneider Electric, 10000 Series Rack PDU (APDU10000), RPDU, SNMP Airedale, EasiCool EZRE Precision Air Conditioning (DF35X-EZRE-1, pCOWeb), CRAC, SNMP AKCP, sensorProbe Plus Series (sensorProbe+), Environmental Monitor, SNMP Emerson/Liebert/Vertiv, eXM M/S/R, UPS, SNMP Grundfos, CIM/CIU 500, Pump, Modbus Kidde-Fenwal Inc., ARIES, Fire Suppression System, Modbus Kohler, Decision-Maker 3000, Generator Control Module, Modbus Stulz, SplitAir3, CRAC, Modbus Updated devices APC/Schneider Electric, Easy UPS SRV, UPS, SNMP - Add phase information to sensor labels for 3 phase models. APC/Schneider Electric, Microlink Smart-UPS, UPS, SNMP - Add monitoring support for battery packs APC/Schneider Electric, ACRD300 Series, CRAC, SNMP - Fix Application Version attribute showing Firmware Version Schneider Electric, Gutor BMS BACS, Battery Management System, SNMP - Add support for BACS Module State alarms Schneider Electric/PowerLogic, Various, Power Meter, Modbus - Fix vendor names so they all display as "Powerlogic" on discovery page instead of "Powerlogic" and "Power_logic". IMPORTANT: This update requires manual rediscovery of devices that have "Power_logic" as the vendor. Devices will go offline after the device library is updated, and will stay offline until you run a rediscovery. Affected families include: Cm3000/Cm4000 Ion8600 Pm210 Pm32xx Pm53xx Pm55xx Pm620 Pm710 Pm750 Pm8000 Pm8xx Enercept Ion6200 Ion7650 Chatsworth, eConnect PDU (Previous Model/Legacy), RPDU, SNMP - Restructure breaker configuration within the DDF to be more accurate and include additional Unified ID support. IMPORTANT: Significant changes were made to this DDF which will cause loss of historical data on sensors after the device library is applied. Enlogic, Legacy MIB (ENLOGIC-PDU-MIB), RPDU, SNMP - Add alarm support Device Library v1.10.0.52 Requires EcoStruxure IT Gateway version 1.10 August 2021 New device support (Vendor, Series, Type, Protocol) Electro Industries/GaugeTech Inc., Shark 200, Power Meter, Modbus Updated devices ServerTech, Sentry4, RPDU, SNMP - Fix alarm bug Rittal, CMCIII, Monitoring System, SNMP - Update Name attribute OID APC, Symmetra, UPS, SNMP - Add APC Power Module monitoring support APC, Remote Power Panel (RPP), PDU, SNMP - Add support for the following parameters: Input average current (1.3.6.1.4.1.318.1.1.28.3.1.2.1.25) Neutral current (1.3.6.1.4.1.318.1.1.28.3.1.2.1.26) Max Instantaneous current (1.3.6.1.4.1.318.1.1.28.3.1.3.1.9) Current phase angle data (1.3.6.1.4.1.318.1.1.28.3.1.3.1.10) Voltage THD L to N (1.3.6.1.4.1.318.1.1.28.3.1.3.1.12) Voltage THD L to L (1.3.6.1.4.1.318.1.1.28.3.1.3.1.11) Energy usage accumulated total (1.3.6.1.4.1.318.1.1.28.3.1.2.1.34) Average Voltage L to N (1.3.6.1.4.1.318.1.1.28.3.1.2.1.30) Load percentage : (1.3.6.1.4.1.318.1.1.28.3.1.2.1.31) Energy Usage reset Date for input (1.3.6.1.4.1.318.1.1.28.3.1.2.1.38). Energy Usage Reset Date for panels (1.3.6.1.4.1.318.1.1.28.3.3.3.1.12) Input1 Voltage Line to Line Average (1.3.6.1.4.1.318.1.1.28.3.1.2.1.29) Current THD (1.3.6.1.4.1.318.1.1.28.3.1.3.1.13) Phase loss threshold (1.3.6.1.4.1.318.1.1.28.3.1.2.1.35) Input x Phase Loss : 1.3.6.1.4.1.318.1.1.28.3.1.2.1.51 Input x Breaker CT Size : 1.3.6.1.4.1.318.1.1.28.3.1.2.1.36 Input x Breaker rating : 1.3.6.1.4.1.318.1.1.28.3.1.2.1.37 Panel Channel Branch Number : 1.3.6.1.4.1.318.1.1.28.3.3.3.1.34 Panel Channel CT Size : 1.3.6.1.4.1.318.1.1.28.3.3.3.1.35 Phase association : 1.3.6.1.4.1.318.1.1.28.3.3.3.1.4 Number of poles : 1.3.6.1.4.1.318.1.1.28.3.3.3.1.3 Alarm generation : 1.3.6.1.4.1.318.1.1.28.3.3.3.1.21 Fix Input Frequency Deviation sensor Uniflair, Various, CRAC/Chiller, SNMP/Modbus (pCOWeb/non-NMC) Add missing alarms Convert "Type A/Type B/Type C" alarms to sensors Eaton, Access Power Solutions (APS), Inverter, SNMP - Update Serial Number and Name attribute OIDs Device Library v1.10.0.41 Requires EcoStruxure IT Gateway version 1.10 July 2021 New device support (Vendor, Series, Type, Protocol) APC/Schneider Electric, Easy Micro Data Center, Micro Data Center, SNMP Uniflair/Schneider Electric, Aquascroll with custom OID 99009, Chiller, SNMP This is for Aquascroll devices equipped with a Carel pCO5+ web card and UG50 HMI using the custom enterprise OID "99009" instead of the standard Carel enterprise number "9839". AKCP, SensorProbe Series, Environmental Monitor, SNMP Alpha, FXM, UPS, SNMP Cisco, Various, Network Switch, SNMP Eaton, Access Power Solutions (APS), Inverter, SNMP Uses SC200 communication card HWGroup, HWg-STE, Environmental Probe, SNMP PDI, PowerPak PDU w/ WaveStar/FDI Display, PDU, SNMP PDI, WaveStart STS, Static Transfer Switch, SNMP Redetec, PN/3.0/Red/FAL, Fire Suppression System, SNMP Updated devices APC/Schneider Electric, Netbotz, Environmental Monitor, Botzspeak - Add “value rising too quickly” and “value dropping too quickly” alarms APC/Schneider Electric, NetBotz 250, Environmental Monitor, SNMP - Fix temperature conversion for wireless sensor Uniflair/Schneider Electric, Aquascroll, Chiller, SNMP/Modbus - Support for additional alarms Schneider Electric, Masterpact MTZ, Power Meter, Modbus Add serial number attribute Fix scaling on energy sensors PowerLogic/Schneider Electric, PM8000, Power Meter, Modbus Add sensors for per-phase/neutral Current Demand, Active Power Demand, Reactive Power Demand, and Apparent Power Demand Use 64-bit registers for Active Energy Delivered, Reactive Energy Delivered, and Apparent Energy Delivered Fix some scaling issues PPC, UPS, SNMP - Add fix to better handle single phase devices and added missing "Output Load" sensor   Device Library v1.9.0.236 April 2021 New device support (Vendor, Series, Type, Protocol) Oracle, RMII Enhanced PDU, RPDU, SNMP Schneider Electric/Uniflair, ERAx/ISAx with custom OID 99001, Chiller, SNMP This is for ERAx and ISAx devices equipped with a Carel pCO1 web card and MP20II HMI using the custom enterprise OID "99001" instead of the standard Carel enterprise number "9839". Updated devices Schneider Electric, APC, Gen 2 RPDU, SNMP - Updated “Total Power” sensor name to “Total Input Power”. Schneider Electric, PowerLogic, PM800, Modbus - Fix scaling on power sensors. APC by Schneider Electric, NetBotz - Temperature and dew point alarms for NetBotz series 200, 300, and 400 devices can now be displayed in the Gateway in Fahrenheit or Celcius. NetBotz series 200, 300, and 400 devices use the Botzspeak protocol. TrendPoint, EnerSure, BCM, SNMP - Fixed discovery issue present on EnerSure devices. Schneider Electric, Gutor, SDC, Modbus - Fixed state sensor enumerations for “Operation Mode” and “Active Systems”. ASCO, 5140 Quad Ethernet Module (72EE), SNMP - Fixed discovery issue present on some devices. Deep Sea Electronics, DSE74xx, Generator Control Module, Modbus - Added support for 7450 and hide unsupported sensors instead of showing incorrect values Device library v1.9.0.227 April 2021 Updated devices Schneider Electric, APC, Symmetra 3P, UPS, SNMP - Added sensors for the power module. Schneider Electric, APC, Easy UPS 3 Phase with NMC, SNMP - Added battery age sensor. Schneider Electric, PowerLogic, PM8000, Power Meter - Added additional sensors. Schneider Electric, ComPact NSX, Breaker, Modbus - Added name and serial number attributes. Geist, Watchdog, Environmental Monitor, SNMP - Fixed discovery issue with certain models. Device library v1.9.0.218 March 2021 New device support (Vendor, Series, Type, Protocol) ASCO, 72EE, ATS, (5140 Quad Ethernet Module), SNMP Liebert, iCOM SC type HPC, Chiller, SNMP Liebert, iCOM PA type PEXS, Chiller, SNMP Updated devices Schneider Electric, Uniflair, Aquascroll Modbus - Some alarm severities were updated from warning to critical. Updated Compressor Inverter Operative Limits enumerations APC by Schneider Electric InfraStruxure PDU - Added Unified ID support Smart UPS - Added Output Active Power sensor to some devices Smart UPS - Added Unified ID support to Power Module sensors NetBotz 755, Environmental Monitor - Fixed missing temperature and humidity sensors All UPSs with NMCs - New sensor for Total DC Current. Removed Total DC Current as a back up to Battery Current. PowerLogic, PM8000, Power Meter - Fixed Modbus register addressing issue Device library v1.9.0.201 February 2021 New device support (Vendor, Series, Type, Protocol) Schneider Electric, Easy UPS 3S, SNMP Schneider Electric, PowerLogic ION9000, Power Meter, Modbus Enlogic, iPDU, SNMP Updated devices Schneider Electric, Uniflair, Aquascroll, SNMP - Some alarm severities were updated from warning to critical. Schneider Electric, Uniflair, UG40 MP40, SNMP - Some alarm severities were updated from warning to critical. Schneider Electric, Easy UPS 3M, SNMP - Some devices were not retrieving the serial number in previous versions. Device library v1.9.0.193 February 2021 New device support (Vendor, Series, Type, Protocol) Schneider Electric, Sepam T40, Protective Relay, Modbus Schneider Electric, Sepam Series 80, Protective Relay, Modbus Cummins, PowerCommand 2.x/3.x, Generator Control Module, Modbus Cummins, PCC 1301, Generator Control Module, Modbus Deep Sea Electronics, DSE7420, Generator Control Module, Modbus Green Revolution Cooling, Immersion Cooling, Modbus HIMOINSA, CEC/CEM/CEA, Generator Control Module, Modbus Siemens, Sentron 3200, Power Meter, Modbus Sinetica, Hawk-i2, Monitoring Unit, SNMP Updated devices Schneider Electric, NetBotz 750, SNMP - Resolved an issue in which some door sensors were not appearing. Phoenix Power Corporation, UPS - Resolved an issue which caused incorrect status. Device library v1.9.0.176 January 2021 New device support (Vendor, Series/Type, Protocol) Schneider Electric, Sepam S20 Relay, Modbus Schneider Electric, Conext Gateway, Modbus Schneider Electric, Conext XW+ Inverter, Modbus Bachmann, BlueNet BN2000 RPDU, SNMP Geist, Watchdog, Environmental Monitor, SNMP Geist, Watchdog 100, Environmental Monitor, SNMP IT Watchdogs, WxGoos-1, Environmental Monitor, SNMP IT Watchdogs SuperGoose II, Environmental Monitor, SNMP Rittal, CMC III LCP (type 1.3.6.1.4.1.2606.7.7.4.9217), SNMP Updated devices Schneider Electric, TSATRA and Amico cooling devices - Added NMC component APC, Easy RPDU - Fixed unhandled exception and added more descriptive sensor names Device library v1.9.0.163 December 2020 New device support (Vendor, Series/Type, Protocol) Schneider Electric, Micro Data Center, SNMP Schneider Electric, Galaxy UPS, Modbus Schneider Electric, Gutor, BMS BACS, Modbus BlackBox, Environmental Monitor, SNMP DB Power Electronics, 120KVA UPS, SNMP Geist, IMD RPDU, SNMP Phoenix Broadband Technologies, PowerAgent BMS, SNMP Rittal CMC III, LCP Chassis/PDU/PU ZUCS/PU, SNMP Updated devices Schneider Electric, Gutor BMS BACS, SNMP - Added Battery String sensors APC UPSs - Fixed data type such that "Output Energy Usage" can now be larger than 2,1474,836 kWh APC UPSs - Fixed scaling and name of "Low Battery Shutdown Threshold" Alcatel Switch, SNMP - Fixed enumeration issue Geist V5, PDU, SNMP - Fixed discovery issue Kamstrup Multical, Modbus - Fixed scaling issue PPC, UPS, SNMP - Added additional alarms, fixed enumerations, and changed sensor names for clarity   Device library v1.9.0.148 November 2020 New device support (Vendor, Series/Type, Protocol) Schneider Electric, Power Meter, ION8600, Modbus Eaton, Switched ePDU, SNMP PDI, BCMS II Plus, SNMP PowerShield, Battery String Monitor, SNMP Rittal, Chillers with Carel pco5+ cards, SNMP Rittal, Smart PDU, SNMP Updated devices Schneider Electric, Easy RPDU - Fixed issue related to device discovery. APC, BMSHVA Battery Manager - Fixed issue with incorrect scaling on ohmic values. MGE, Galaxy - Added a work around to allow devices with incorrect serial numbers to discover. Device library v1.9.0.134 October 2020 New device support (Vendor, Series/Type, Protocol) Tripp Lite, PDU with WEBCARDLX, SNMP Enlogic, Input Metered PDU, SNMP Lenovo, Smart RPDU, SNMP Updated devices Schneider Electric, Gutor, Battery Manager - Added new state sensors for Gutor with status information. Schneider Electric, Easy RPDU - Added alarms based on the user defined thresholds from the device Generic UPSMIB - Updated the alarm severities Device library v1.9.0.127 October 2020 New device support (Vendor, Series, Type, Protocol) Schneider Electric, Acti9 SmartLink and SmartLink SI B, Gateway for PowerTag energy sensors, Modbus Schneider Electric, Easy RPDU, SNMP Schneider Electric, Gutor, Battery Manager, SNMP Schneider Electric, APC, Air Economizer, CRAC, SNMP Schneider Electric, Easy Cooling, InRow Chiller, Modbus Schneider Electric, Uniflair, ARAnew, SNMP Schneider Electric, Uniflair, DSAF, Chiller, SNMP Schneider Electric, Uniflair, Rack Mount DX, CRAC, Modbus Schneider Electric, Uniflair LE and LE L, CRAC, SNMP Emerson, NXR, UPS, SNMP Emerson, NXC 30-40k, UPS, SNMP Geist, R-Series v5, PDU, SNMP HP, PDU, SNMP Kamstrup, Multical 62/601/602/801, Energy Flow Meter, Modbus Janitza, UMG96, Power Analyzer, SNMP Liebert, PeX, CRAC, Modbus NTI, Enviromux 2D and 5D, Environmental Monitor, SNMP Redetec, PN/RED/3.0, Fire Suppression System, SNMP Rittal, CMC Processing Unit, Controller, SNMP Socomec, NetVision7, UPS, SNMP TrippLite, WEBCARDLX, ATS, SNMP Vertiv, GXT4, UPS, SNMP  

The EcoStruxure IT Gateway Windows installer requires the Windows Management Instrumentation Command line (WMIC) utility. WMIC is not preinstalled by default on Windows 11 24H2.   The WMIC utility must be installed on new Windows 11 systems before you install EcoStruxure IT Gateway. Note: Older Windows 11 versions that were updated to 24H2 may already have WMIC installed.   Verify the Windows 11 version   Type system information in the search field on the taskbar.   Verify whether WMIC is installed on your system   Open a command window and type wmic os. If WMIC is not installed or enabled, the command returns: 'wmic’ is not recognized as an internal or external command, operable program, or batch file.   Install WMIC on your Windows 11 system   Type Optional features in the search field on the taskbar. Note: WMIC will not appear in the Added features list if it is not installed. In the Add an optional feature section, click View features. Type WMIC in the search field. Check the box for WMIC and then click Next to install WMIC.   See WMI command-line utility