Sign Up & Add your Device

Register your SmartConnect-compatible UPS with your account: Using a QR Code  Using Product Codes  NOTE: The UPS device you are adding cannot be associated with another Schneider Electric account. See Adding your Device Issues for more information.   QR Code Scan Register your device by scanning the QR code on your UPS using your smart phone or tablet device. You can scan your Smart-UPS device’s QR code using the web portal’s integrated QR code scanner or via a third-party QR code reader. It is recommended you use the web portal’s built-in scanner as it is the quickest way to register your device.   NOTE: Please allow 4-5 minutes after you connect your SmartConnect-compatible UPS before attempting to register your device.   Integrated QR Code Scanner 1. Log in to the web portal on a mobile device, and navigate to Add > QR Code Scan. 2. Click Scan QR Code. A browser popup will display asking you to allow access to your device’s camera(s). Select Allow.   NOTE: If you select Cancel by accident, click Close and log out of the web portal. Follow steps 1-2 again, and click Allow when prompted. If camera access is still blocked, see Knowledge Base article FA408179 for more information. NOTE: Ensure that your mobile device’s battery is sufficiently charged before using the integrated QR code scanner.   3. Select a camera using the drop-down list and scan the QR code on the UPS label: NOTE: The QR code label may be on the front, side, or rear of your UPS.   4. If the scanner detects a valid QR code, you will be redirected to Register UPS page. If your session has expired, you will need to log in again using your account credentials. 5. The Register UPS page is pre-populated with your Product ID and Product Key, obtained during the QR scan. Click Register UPS. If SmartConnect is not enabled on your device, you will be prompted to do so. 6. On the UPS Profile page, provide the UPS Name, UPS Description, Timezone and Notifications for the UPS. Click Save Profile.  7. On the Device Sensitivity page you can set how sensitive your device is to on Battery conditions. Click Next and Finish.   Third-Party QR Code Reader 1. Install a QR code reader. NOTE: Devices running iOS 11+ do not require the installation of a QR code reader, as the default camera application can read QR codes.   2. Select the QR code scanner: 3. Scan the QR code on the UPS label:   NOTE: The QR code label may be on the front, side, or rear of your UPS.   4. In your browser, visit the URL created by the QR code scan. a. If you do not already have a Schneider Electric account, you can Sign Up. b. If you have a Schneider Electric account, log in using your account credentials. 5. Log in using your Schneider Electric account credentials. 6. The Register UPS page is pre-populated with your Product ID and Product Key, obtained during the QR scan. Click Register UPS. If SmartConnect is not enabled on your device, you will be prompted to do so. 7. On the UPS Profile page, provide the UPS Name, UPS Description, Timezone and Notifications for the UPS. Click Save Profile. 8. On the Device Sensitivity page you can set how sensitive your device is to on Battery conditions. Click Next and Finish.   Product Codes Register your device by entering the Product ID and Product Key located on the label attached to your UPS.   NOTE: Please allow 4-5 minutes after you connect your SmartConnect-compatible UPS before attempting to register your device. 1. Log in to your Schneider Electric account at smartconnect.apc.com.  2. Go to Add Device and select Product Codes. 3. Enter the Product ID – a 12-digit alphanumeric ID shown on the UPS label. 4. Enter the Product Key – a 14-digit alphanumeric key shown on the UPS label. 5. Click Register UPS to proceed. If SmartConnect is not enabled on your device, you will be prompted to do so. 6. On the UPS Profile page, provide the UPS Name, UPS Description, Timezone and Notifications for the UPS. Click Save Profile.  7. On the Device Sensitivity page you can set how sensitive your device is to on Battery conditions. Click Next and Finish.  

You can update your Schneider Electric account profile to change your: Name Email  Password Language Preference Address details  Enable two-Factor Authentication Add company contact details for a personalized service and faster technical support NOTE: It is highly recommended that you enable Two-Factor Authentication to add an extra layer of security to your account. This must be enabled in the web portal to remotely reboot your UPS device’s outlet groups:   1 .Click My Account and navigate to View Profile. 2 .In the My Profile page, select Two-Factor Authentication. 3 .Click Turn On. 4 .Choose your preferred verification method for two-factor authentication and confirm your selection.   Password Reset Visit the Web Portal login page. Click Forgot your password? Enter the email address you used to create your Schneider Electric account. Select the ‘I am not a robot’ checkbox to complete the security check. Click Reset Password Check your email account for the password reset email, and follow the instructions in the email to reset your password.   Delete Account To delete both your SmartConnect account and Schneider Electric account: Click Delete My Account Click Next in the Account Deletion Request page. NOTE: This action cannot be undone and your user accounts across all Schneider Electric applications will be permanently deleted. 

If you already have an account on partner.schneider-electric.com, you can log in to the Web Portal using those credentials.   To get a Schneider Electric account: Visit smartconnect.apc.com and select Sign Up. On the Register page, enter your: – Email address to which the web portal will send a confirmation email – Name (First and Last) – Password: • The password must be at least 8 characters in length. • The password cannot contain your first name or last name. • The password must use at least 3 of four character types: upper case letters, lower case letters, numbers and symbols. • Cannot contain email or part of email. – Location Click Next.   3. On the next Register page, enter your:   – Company Name* – Business Type* – Area of Focus – Industry Segment – Address* – City* – Zip Code* – Location* – State/Province*   *required fields   4. Review the SE privacy notice and policy. 5. You can also opt to receive product information and promotional materials from Schneider Electric by selecting the ‘Yes’ radio button. 6. Select the ‘I am not a robot’ checkbox to complete the security check. 7. Click on Register to complete registration. 8. The Verify your account page will appear with spaces to add a 6-digit code. 9. Verify that a confirmation email was sent to the email address specified in step 2. Enter the 6-digit code from the confirmation email in the Verify your account page.  10. Once your code is verified, you will be asked if you want to enable Two-Factor Authentication or not. You can log in to the web portal with the email address and password used during sign up.