PowerLogic T300 - IEC 61850 connection error to P3?

[elnur]

T300 connected to P3 via 61850

Dear colleagues.

I receive conf error message when try to connect P3U to T300 via 61850. I configure 61850 server using Build SCD option in Easergy Builder and download created conf file into T300 . The question is why I receive error message from T300 if all the configuration done by Easergy Builder? I did not touch anything after creating the file. On this stage there is no any points or client connection defined. Please see below pic.

Can you share step by step instruction how to configure  P3-> T300 connection via 61850?

Thanks in advance,

[elnur]

Dear colleagues.

I receive conf error message when try to connect P3U to T300 via 61850. I configure 61850 server using Build SCD option in Easergy Builder and download created conf file into T300 . The question is why I receive error message from T300 if all the configuration done by Easergy Builder? I did not touch anything after creating the file. On this stage there is no any points or client connection defined. Please see below pic.

Can you share step by step instruction how to configure  P3-> T300 connection via 61850?

Thanks in advance,

[elnur]

Just for better understanding, I have just added IEC61850 server in Easergy Builder choosing Build SCD option. Then not touching anything downloaded the configuration into T300 and receive error in the picture, Why there is error message if all configurations done by Easergy Builder? I mean on this stage there is no any points  or client connection defined but T300 warm about configuration error.   

[JuanRayo]

Hello Elnur. Just to my have a clear picture in mind, if you want to integrate P3U in T300 you must have P3U´s cid file to configure T300 as a client, Is that correct?... if so the option "Build SCD" is correct as a first step but then you must import the cid file and start the process to integrate the device itself within T300 configuration. I have prepared a brief summary with the steps to be taken for this. I wish it helps you

[TomBerry]

To see the reason why the T300 rejected the configuration, look at the T300 (HU250) system log.

[JYPOC]

Hello Elnur, as you can see from this old post (https://community.se.com/t5/PAE-Protection-Relays-Controllers/Easergy-T300-Easergy-P3-and-IEC-61850-...), the IEC 61850 connection of PowerLogic T300 to multiple PowerLogic P3 has already been successfully performed quite some time ago.

[elnur]

Hello Juan,

thnka you for your help. I did exactly how you propsed and still tehre is an error message. i have cheked inlog ifle and there isonly one error as below:

02/02/2025 14:25:58.049 ERRO Rdb:contManGo: sorry, no way to start i61sc controller. No exe file found

does it mean that i have to download some exe file into T300??? Or this file shoudl be in some directory of easergy builder? 

[elnur]

Hello JYPOC ,

i do not have acess to link you shared. How can get this acess?

[elnur]

Hello Tom,

only tehre is only one error message as below"

ERROR db:contManGo: sorry, no way to start i61sc controller. No exe file found

[JuanRayo]

Hello Elnur. Let us know the firmware version loaded (perhaps you need to upgrade it) and also share with us the configuration files 

[elnur]

Hello Juan,

please find attached conf file and screenshot with firmware (1.2.2-6224) below. I was thinking to upgrade the firmware but could not find proper file.

[JuanRayo · Accepted solution]

Hello Elnur.

The firmware version you got v1.2.2 is very old. Take into account that 61850 controller is active in T300 since release 1.3.1 so you need to upgrade it.

Please contact your Front office or my colleague Mathieu Lansoy for this.

[elnur]

Hello Juan, thank you for support, I have updated the firmware and everything is good now. 

Thanks for all team for the help.