Welcome to the new Schneider Electric Community

It's your place to connect with experts and peers, get continuous support, and share knowledge.

  • Explore the new navigation for even easier access to your community.
  • Bookmark and use our new, easy-to-remember address (community.se.com).
  • Get ready for more content and an improved experience.

Contact SchneiderCommunity.Support@se.com if you have any questions.

Close
Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
84527members
353772posts

XS 1000 issue

APC UPS for Home and Office Forum

Schneider Electric support forum for our APC offers including Home Office UPS, Surge Protectors, UTS, software and services and associated products designed to share knowledge, installation, and configuration.

Solved
Dale_B_apc
Crewman
Crewman
0 Likes
1
82

XS 1000 issue

This was originally posted on APC forums on 9/7/2010


I just purchased an XS 1500 for my system, and an XS 1000 for my wifes (I do CG and video, she does blogs, websites, etc). My 1500 installed and performs just fine.The 1000 for her system installs, then it goes to onlie with battery, then clicks over to line power, and a minute or so after that, the AVR warning starts flashing, with a prompt to go to the manual (there is no indicator as to whether the AVR is high or low; just the AVR flag), and the unit gives 3 beeps (which I have found no mention of in the database). I've brain deaded the unit, checked the battery charge, adjusted the theshhold, and powered it on with no load whatsoever, and still get the same performance. Is there a step or three I missed, or do I just have a bad unit out of the box?


Accepted Solutions
Dale_B_apc
Crewman
Crewman
0 Likes
0
82

XS 1000 issue

This was originally posted on APC forums on 9/7/2010


I just purchased an XS 1500 for my system, and an XS 1000 for my wifes (I do CG and video, she does blogs, websites, etc). My 1500 installed and performs just fine.The 1000 for her system installs, then it goes to onlie with battery, then clicks over to line power, and a minute or so after that, the AVR warning starts flashing, with a prompt to go to the manual (there is no indicator as to whether the AVR is high or low; just the AVR flag), and the unit gives 3 beeps (which I have found no mention of in the database). I've brain deaded the unit, checked the battery charge, adjusted the theshhold, and powered it on with no load whatsoever, and still get the same performance. Is there a step or three I missed, or do I just have a bad unit out of the box?

See Answer In Context

1 Reply 1
Dale_B_apc
Crewman
Crewman
0 Likes
0
83

XS 1000 issue

This was originally posted on APC forums on 9/7/2010


I just purchased an XS 1500 for my system, and an XS 1000 for my wifes (I do CG and video, she does blogs, websites, etc). My 1500 installed and performs just fine.The 1000 for her system installs, then it goes to onlie with battery, then clicks over to line power, and a minute or so after that, the AVR warning starts flashing, with a prompt to go to the manual (there is no indicator as to whether the AVR is high or low; just the AVR flag), and the unit gives 3 beeps (which I have found no mention of in the database). I've brain deaded the unit, checked the battery charge, adjusted the theshhold, and powered it on with no load whatsoever, and still get the same performance. Is there a step or three I missed, or do I just have a bad unit out of the box?