Machine Automation Forum
A forum addressing machine automation solutions for the complete machine lifecycle. Including offers like Machine Advisor, Modicon PLC/PacDrive, Lexium or Preventa. Discuss and share knowledge on offers relating to cloud-based service platforms, machine localization and monitoring, industrial operations control, motion products as well as safety function!
Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
Hello everyone,
I would like to highlight the next upcoming virtual training courses for Machine Automation in February 2022:
EcoStruxure™ Machine Expert with M262 – Module 3: Digital - VIRTUAL
Sess...
Solved
I have a TM221CE24R PLC with a TM3AI8 extension. I want to scale an extension's analog input signal . What function or how this could be done?And another question would be how could I set for analog in...
Solved
Hello,I have two PLCs: a TM251MESE (which is the master) and a TM221CE24R (which is the slave). On my slave I've set some values for three memory words (%MW100=13, %MW101=11 and %MW102=6). I want to se...
Solved
Hello guys,
I have some troubles to set up the a TM172PDG42R as Modbus master.
- I set the RS485-2 to Modbus master and the different modbus properties,
- I created a "Generic Modbus" device properly a...
Solved
Good morning,with a LMC402 I should reset a logical encoder, connected to rotative axis, when a touch probe input rises.If I call a FC_SetposSingle in a task I'll be late.There is a way for connecting ...
Good morning,I should create a camming in LMC with library PD_AxisModule.I call the function FC_InitDriveParameter necessary for assigning the master and the slave and with FC_InitCamPoint I link the p...
Maybe somebody has figured out how to solve this... So, I am used to working at the office with dual monitors. That means that while I am developing a project, I typically have the project on my laptop...
Information for those who want to install SoMove 2.9.4.0 and some earlier versions on Windows 7 x64 build 7601 and get error 0x80000907 during registration.The problem is that authorization of the lice...
Solved
Good morning,I should, with a LMC PRO2 and sercos axis, connect in gearing two axis (same velocity).I don't find the function, in the pacdrivelib (version 1.10.1), to do that.Thanks in advanceAndrea Ar...
Solved
I got a couple of ratiometric pressure sensors which are taking far more current than expected. This means DC 5V is dropping to about 3.6 V (TM172PDG28R)Besides ditching the sensors and getting new one...
Solved
Hi,I've observed that during Simulation the user defined default EEPROM values do not load before task execution. Instead, a zero value seems to be passed on first cycle execution. I observed this due ...
Hi - I'm using a TM221C40T with analogue module TM3AI8, each input is measuring gas concentrations (4 - 20mA) I need to average each input sequentially over a 5 minute period, then output the average o...
Solved
Good mornig everyone,which library could I use to control a Lexium32 with PacDrive LMC402 in Profinet ?Is the "GMC Independent Lexium" the right library ?Thanks a lotAndrea
I am trying to make alarms visible on a "pop-up" screen in M172 HMI. I do it by using a "Message" instead of a regular page. An example code is availablehere.I define a couple of status variables to do...
Solved
I'm using ESME HVAC 1.4 and am trying to read a Mettler Toledo scale that has a 32bit real weight in two consecutive registers.I'm not seeing a way to configure the Modbus Ethernet settings to read a R...
Subscribing is a smart move!
You can subscribe to this forum after you log in or create your free account.
Create your free account or log in to subscribe to the forum - and gain access to more than 10,000+ support articles along with insights from experts and peers.