Welcome to the new Schneider Electric Community

It's your place to connect with experts and peers, get continuous support, and share knowledge.

  • Explore the new navigation for even easier access to your community.
  • Bookmark and use our new, easy-to-remember address (community.se.com).
  • Get ready for more content and an improved experience.

Contact SchneiderCommunity.Support@se.com if you have any questions.

Close
Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
84640members
353973posts

Trio Q Radio - Dynamic Beacon

Remote Operations Forum

Collaborate and share knowledge on the extensive range of remote systems and devices, including SCADA radios and RTUs, on the Schneider Electric Exchange Remote Operations (formerly SCADA & Telemetry) forum. From commissioning SCADA integration devices and software, to enhancing existing installations or troubleshooting, connect with a global community of experts and users. Subscribe today.

Solved
bigdaz
Ensign
Ensign
0 Likes
1
1239

Trio Q Radio - Dynamic Beacon

I believe the latest firmware on the Q radio has this feature

 

In the Modulation section,

a. From the drop-down list for Dynamic Policy, select ARQ.

b. From the drop-down list for Dynamic Beacon, select Master.

 

Will changing the dynamic policy to arq affect how it preforms? My radio was setup with RSSI as standard.

 

Does the Dynamic ID just identify which site is replying back to the basestation?


Accepted Solutions
Joel_Weder
Commander Commander
Commander
0 Likes
0
1236

Re: Trio Q Radio - Dynamic Beacon

Note first that these comments refer to Trio Q firmware 2.2.5.6746 or newer, when installed in ETSI-type radios. QAM and the related features will be available in the very near future for FCC-type radios.

 

Dynamic Policy and the related features have a significant amount of "Help" in the web browser if you click the "More help..."  blue link by each item. Also, this topic is discussed in some detail in the Trio Q user manual, which will be installed on your computer when you install the TView+ Management Suite software package.

 

This software can be downloaded from the se.com website. Go to Products, then Telemetry and Remote SCADA Systems, then scroll down to Data Radios and select either the Licensed or License-Free radio type. On the page for your radio type, select the Software and Firmware tab, and TView should be near the top.

 

On page 44 of the December 2019 version of the Q user manual there is quite a bit of information about each option for Dynamic Policy. Near the bottom of the page, in the ARQ section, the manual states:

 

When the Dynamic Policy is configured as ARQ, the RF data rate selection by the radio is
determined by the ARQ retry rate. If the currently selected RF data rate is too high to support
reliable reception of transmitted packets, ARQ retries will be required and the packet
retransmitted. ARQ retries are transmitted at progressively lower speeds to ensure delivery. The
aim of the algorithm is to choose the optimum RF data rate of the initial packet transmission and
maintain an ARQ retry rate of between zero and 1%. This policy is only available in QAM mode...

 

The Beacon ID is used by Remote radios to ensure they are following the beacon of the correct Master radio, as it is possible there could be more than one Master that the Remote radio can hear.

 

Joel Weder
Remote Operations Specialist
Schneider Electric

See Answer In Context

1 Reply 1
Joel_Weder
Commander Commander
Commander
0 Likes
0
1237

Re: Trio Q Radio - Dynamic Beacon

Note first that these comments refer to Trio Q firmware 2.2.5.6746 or newer, when installed in ETSI-type radios. QAM and the related features will be available in the very near future for FCC-type radios.

 

Dynamic Policy and the related features have a significant amount of "Help" in the web browser if you click the "More help..."  blue link by each item. Also, this topic is discussed in some detail in the Trio Q user manual, which will be installed on your computer when you install the TView+ Management Suite software package.

 

This software can be downloaded from the se.com website. Go to Products, then Telemetry and Remote SCADA Systems, then scroll down to Data Radios and select either the Licensed or License-Free radio type. On the page for your radio type, select the Software and Firmware tab, and TView should be near the top.

 

On page 44 of the December 2019 version of the Q user manual there is quite a bit of information about each option for Dynamic Policy. Near the bottom of the page, in the ARQ section, the manual states:

 

When the Dynamic Policy is configured as ARQ, the RF data rate selection by the radio is
determined by the ARQ retry rate. If the currently selected RF data rate is too high to support
reliable reception of transmitted packets, ARQ retries will be required and the packet
retransmitted. ARQ retries are transmitted at progressively lower speeds to ensure delivery. The
aim of the algorithm is to choose the optimum RF data rate of the initial packet transmission and
maintain an ARQ retry rate of between zero and 1%. This policy is only available in QAM mode...

 

The Beacon ID is used by Remote radios to ensure they are following the beacon of the correct Master radio, as it is possible there could be more than one Master that the Remote radio can hear.

 

Joel Weder
Remote Operations Specialist
Schneider Electric