Before you start, make sure you have the Universal Robots Experior catalogs: • Experior.Catalog.UniversalRobots.dll • UniversalRobotsCommunication.dll   Afterward, follow these steps   Robot controller connection The following steps will connect the Experior URX assembly to the robot controller in URSim.   1. Place the Experior UR catalog (.dll) files in the Experior 6 installation folder (usually C:\Xcelgo\Xcelgo Experior 6).   2. Download and unpack/install the following: a. UR Non-Linux Offline simulator virtual machine (URSim):  b. VMware Workstation Player    3. Open VMware Workstation. Open the URSim virtual machine (Player-File-Open, then browse the file explorer to where you unpacked the files from 2.a., then select the .vmx file).    4. When the virtual machine is running, open the file with the name of the robot that you want to simulate. Then, turn the virtual robot on using the button on the bottom left. Then click ON and START.   5. Open Experior 6.0. Make sure the UniversalRobots catalog is selected in the catalog selector. Drag and drop the desired robot from the Catalogs panel to the model.   6. Go to URSim and open the robot settings.   In the settings menu, select System-Network. Note the URSim IP address.   7. Connect URSim to Experior. Do this by going to your Experior model, selecting the robot, and writing the URSim IP address in the IP Address field, under Robot connection. 7.1 Afterward, right-click on the robot and select Connect to robot controller. After this, the robot in Experior will snap into the position of the robot in URSim.       After this, the robot in Experior will replicate the trajectory of the robot in URSim.   Connecting robot I/O through Modbus TCP The following steps show how to connect the robot I/O through the URSim Modbus server and the Experior Modbus client.   1. In URSim, go to Installation- Fieldbus- Modbus- Add a new signal. (Initially, the variable list will be empty) In the dropdown menu, select the variable type: Digital Input/Output, Register (byte) Input/Output. Rename the variable (this is the name that will be used in the UR programming interface)   2. Assign the memory address for the variable. For this, you need to take into account that all the addresses have specific uses (see here).   3. In Experior, add the Modbus client by right-clicking the Communication panel, and selecting Modbus.     4. Select the Modbus client, and in the Properties panel, write the URSim IP address in the IP Address field, under Communication.     5. Assign Input/Output variables to the desired components. To do this, first set the Connection id to the id corresponding to the Modbus client. Then, assign the memory address of the Modbus server (assigned in step 2) in the Address field for the specific Input/Output. Modify the Register value, depending on the variable type defined in step 2. For Register Inputs/Outputs, Modify the Size value to UInt16 (WORD).   6. After all the memory addresses have been set in Experior, right-click on the Modbus client and click connect. While the connection is active, you won´t be able to modify the associated I/O in Experior.     After this, the variable values will be represented in the Experior model.   (This example was made with the Display assembly, found in the Advanced catalog)   

Downloading ABB RobotStudio   Go to http://new.abb.com/products/robotics/robotstudio/downloads Click Download Robot Studio x.xx.xx. Wait for the file to download.   Installing RobotStudio Right click on the desktop, select New and click Folder. Rename it to Robot_temp. Open the folder by double clicking it. Locate downloaded zip file and double click to open. Select all files and folders in the zip and drag across to the open Robot_temp folder. When the files have finished copying double click the file named Launch. If you get the User Account Control pop-up click YES. Select English (USA) from the drop down list and click OK. Click the Install Products button. Click the Robot Studio button. When the Welcome window opens click NEXT. Select I accept the terms in the license agreement. Click NEXT. Click ACCEPT. Leave destination folder as presented and click NEXT. Select Complete and click NEXT. Click INSTALL. When the install is complete click FINISH.   Installing RobotWare On the Install Products window which should still be open from previously, click the Robot Ware button. When the Welcome window opens click NEXT. Select I accept the terms in the license agreement. Click NEXT. Click ACCEPT. Leave destination folder as presented and click NEXT. Select Complete and click NEXT. Click INSTALL. When the install is complete click FINISH. Click Exit and Exit again to close the installer. Delete the Robot_temp directory.