Welcome to the new Schneider Electric Community

It's your place to connect with experts and peers, get continuous support, and share knowledge.

  • Explore the new navigation for even easier access to your community.
  • Bookmark and use our new, easy-to-remember address (community.se.com).
  • Get ready for more content and an improved experience.

Contact SchneiderCommunity.Support@se.com if you have any questions.

Close
Invite a Co-worker
Send a co-worker an invite to the Exchange portal.Just enter their email address and we’ll connect them to register. After joining, they will belong to the same company.
Send Invite Cancel
84385members
353575posts

Smart UPS 700 showing SU1000 in power chute and hyper terminal

APC UPS Data Center & Enterprise Solutions Forum

Schneider Electric support forum for our Data Center and Business Power UPS, UPS Accessories, Software, Services, and associated commercial products designed to share knowledge, installation, and configuration.

Solved
shindvs_apc
Ensign
Ensign
0 Likes
7
343

Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/5/2008


Smart UPS 700 showing SU1000 in power chute and hyper terminal


Accepted Solutions
shindvs_apc
Ensign
Ensign
0 Likes
0
343

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/6/2008


Even There no serial number and UPS manufacture Date too. in UPS Operating parameter

See Answer In Context

7 Replies 7
EZ_Button_apc
Commander
Commander
0 Likes
0
343

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/6/2008


Sounds like something wasn't programmed properly. Where did you purchase this UPS? Since 700's are rather old, I was just thinking it might be a refurbed unit.

TheNotoriousKMP_apc
Sisko
Sisko
0 Likes
0
343

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/7/2008


Vijay,

We have had this conversation before pertaining to the UPS Link Language being proprietary. You are, through what I am witnessing, using these UPS's for personal use, and therefore, would not warrant putting in a request for UPS-Link Language just to communicate with the UPS EEPROM interface.

Please refrain from requesting information pertaining to the Link Language and Hyperterminal commands. No APC Moderator, or myself as an Admin, will provide that information for you.

If you wish to know more about it, I am sure if you do a Google search, the basics are posted somewhere on a site that APC does not have control of.

Thank You.

TaSpEc_apc
Lieutenant JG
Lieutenant JG
0 Likes
0
343

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/6/2008


As I stated in my previous post, those commands are propritary to APC. Even if we could give them out, you run the risk of accidently changing a value that could render the ups unusable. So I still would recommend going back to the dealer that refurbed it or APC's recommended refurb company Coastal Buisiness Machines.

shindvs_apc
Ensign
Ensign
0 Likes
0
343

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/6/2008


Why is so critical code
I know some coomand but not in details.
Like Shift Y 1 R
Shift B
If know in details please send me on my emails
thanks
shindvs@gmail.com

shindvs_apc
Ensign
Ensign
0 Likes
0
343

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/6/2008


Yes i repaired unit from APC authorised dealer in india.
Do you know details hyper terminal languages so i feed in my PC

TaSpEc_apc
Lieutenant JG
Lieutenant JG
0 Likes
0
343

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/6/2008


Unfortunately, those commands to change that value are proprietary and can not be given out to end users. It also possible that the dealer that serviced it used parts from a 1000va unit and that may be why it has changed. The only thing I could recommend is that you possible consult the dealer that refurbed it or contact Coastal Business Machines here in the US.

shindvs_apc
Ensign
Ensign
0 Likes
0
344

Re: Smart UPS 700 showing SU1000 in power chute and hyper terminal

This was originally posted on APC forums on 5/6/2008


Even There no serial number and UPS manufacture Date too. in UPS Operating parameter